添加飞腾 6.6 内核支持 · Pull Request !4 · openEuler/phytium-kernel

为飞腾设备添加 6.6 内核支持：

提交内容：
1.  内核设备树，内核文档
2.  ACPI，音频
3.  char,dma,firmware,hwmon,i2c,iio,irqchip,media,mtd,cpufreq,eda,gpio,hwspinlock,i3c,input,mailbo,mfd 驱动
4.  perf,spi,usb,tee,rtc,tty,can,eth,w1,watchdog,pci,remoteproc,of 驱动
5.  drm,pwm,mmc,iommu 驱动

参考内核代码：
https://gitee.com/phytium_embedded/phytium-linux-kernel/tree/linux-6.6/

测试设备：飞腾派 4GB 内存版本
测试系统：openEuler 24.04
测试功能：系统启动，USB 3.0，HDMI，PCIE，SDIO WiFi，SD 插槽。

系统启动 log：
```
Hit any key to stop autoboot:  0
Retrieving file: /extlinux/extlinux.conf
1:      openEuler
Retrieving file: /uInitrd
Retrieving file: /Image
append: root=PARTUUID=16609bf9-03 console=ttyAMA1,115200 earlycon=pl011,0x2800d000 rootfstype=ext4 rootwait cma=256m rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash
Retrieving file: /phytiumpi_firefly.dtb
Moving Image from 0x90100000 to 0x90200000, end=91b80000
## Loading init Ramdisk from Legacy Image at 95000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    8232318 Bytes = 7.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 90000000
   Booting using the fdt blob at 0x90000000
   Loading Ramdisk to f945c000, end f9c35d7e ... OK
   Loading Device Tree to 00000000f9452000, end 00000000f945b19d ... OK
run in ft_board_setup
fdt_addr 00000000f9452000
mb_count = 0x2
mb_blocks[0].mb_size = 0x7c000000
mb_blocks[1].mb_size = 0x80000000
fdt : can not find /memory@00  node
fdt : add node memory@01
fdt : dram size 0x100000000 update successfully

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000200 [0x700f3034]
[    0.000000] Linux version 6.6.0-phytium-embedded-v3.0+ (chainsx@chainsx-virtual-machine) (aarch64-linux-gnu-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1 SMP PREEMPT Wed Aug 14 15:41:41 CST 2024
[    0.000000] KASLR disabled due to lack of seed
[    0.000000] Machine model: Phytium Pi Board
[    0.000000] earlycon: pl11 at MMIO 0x000000002800d000 (options '')
[    0.000000] printk: bootconsole [pl11] enabled
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: Warning: invalid memblk node 16 [mem 0x0000000080000000-0x00000000faffffff]
[    0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000207fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x207f7f78c0-0x207f7f9fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000ffffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000207fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x00000000faffffff]
[    0.000000]   node   0: [mem 0x0000002000000000-0x000000207fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000207fffffff]
[    0.000000] On node 0, zone Normal: 20480 pages in unavailable ranges
[    0.000000] cma: Reserved 256 MiB at 0x00000000e9400000 on node -1
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 23 pages/cpu s53480 r8192 d32536 u94208
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: root=PARTUUID=16609bf9-03 console=ttyAMA1,115200 earlycon=pl011,0x2800d000 rootfstype=ext4 rootwait cma=256m rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash
[    0.000000] Unknown kernel command line parameters "splash", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Fallback order for Node 0: 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1011712
[    0.000000] Policy zone: Normal
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x00000000e5400000-0x00000000e9400000] (64MB)
[    0.000000] Memory: 3669408K/4112384K available (15360K kernel code, 1384K rwdata, 5436K rodata, 3200K init, 565K bss, 180832K reserved, 262144K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv3: GICv3 features: 16 PPIs
[    0.000000] GICv3: CPU0: found redistributor 200 region 0:0x00000000308c0000
[    0.000000] ITS [mem 0x30820000-0x3083ffff]
[    0.000000] ITS@0x0000000030820000: allocated 65536 Devices @2000080000 (flat, esz 8, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GICv3: using LPI property table @0x0000002000050000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002000060000
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 50.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
[    0.000000] sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
[    0.008283] Console: colour dummy device 80x25
[    0.012821] Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=200000)
[    0.023343] pid_max: default: 32768 minimum: 301
[    0.028044] LSM: initializing lsm=capability,integrity
[    0.033314] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.040778] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.049476] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.056235] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.063436] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.071256] rcu: Hierarchical SRCU implementation.
[    0.076104] rcu:     Max phase no-delay instances is 1000.
[    0.081814] Platform MSI: gic-its@30820000 domain created
[    0.087395] PCI/MSI: /interrupt-controller@30800000/gic-its@30820000 domain created
[    0.095435] EFI services will not be available.
[    0.100245] smp: Bringing up secondary CPUs ...
[    0.115452] Detected VIPT I-cache on CPU1
[    0.115514] GICv3: CPU1: found redistributor 201 region 0:0x00000000308e0000
[    0.115527] GICv3: CPU1: using allocated LPI pending table @0x0000002000070000
[    0.115566] CPU1: Booted secondary processor 0x0000000201 [0x700f3034]
[    0.126293] Detected PIPT I-cache on CPU2
[    0.126304] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64ISAR0_EL1. Boot CPU: 0x00011100012120, CPU2: 0x00000100012120
[    0.126317] CPU features: SANITY CHECK: Unexpected variation in SYS_MVFR0_EL1. Boot CPU: 0x00000010110222, CPU2: 0x00000010111222
[    0.126321] CPU features: Unsupported CPU feature variation detected.
[    0.126345] GICv3: CPU2: found redistributor 0 region 0:0x0000000030880000
[    0.126352] GICv3: CPU2: using allocated LPI pending table @0x0000002000100000
[    0.126373] CPU2: Booted secondary processor 0x0000000000 [0x701f6643]
[    0.137000] Detected PIPT I-cache on CPU3
[    0.137007] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_AA64ISAR0_EL1. Boot CPU: 0x00011100012120, CPU3: 0x00000100012120
[    0.137018] CPU features: SANITY CHECK: Unexpected variation in SYS_MVFR0_EL1. Boot CPU: 0x00000010110222, CPU3: 0x00000010111222
[    0.137038] GICv3: CPU3: found redistributor 100 region 0:0x00000000308a0000
[    0.137045] GICv3: CPU3: using allocated LPI pending table @0x0000002000110000
[    0.137062] CPU3: Booted secondary processor 0x0000000100 [0x701f6643]
[    0.137121] smp: Brought up 1 node, 4 CPUs
[    0.270672] SMP: Total of 4 processors activated.
[    0.275411] CPU features: detected: 32-bit EL0 Support
[    0.280594] CPU features: detected: 32-bit EL1 Support
[    0.285773] CPU features: detected: CRC32 instructions
[    0.296660] CPU: All CPU(s) started at EL2
[    0.300822] alternatives: applying system-wide alternatives
[    0.308275] devtmpfs: initialized
[    0.314432] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.324262] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.334912] pinctrl core: initialized pinctrl subsystem
[    0.340380] DMI not present or invalid.
[    0.344562] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.351051] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[    0.358308] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.366225] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.374234] audit: initializing netlink subsys (disabled)
[    0.379750] audit: type=2000 audit(0.248:1): state=initialized audit_enabled=0 res=1
[    0.379949] thermal_sys: Registered thermal governor 'step_wise'
[    0.387562] thermal_sys: Registered thermal governor 'power_allocator'
[    0.393631] cpuidle: using governor menu
[    0.404251] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.411149] ASID allocator initialised with 32768 entries
[    0.416875] Serial: AMBA PL011 UART driver
[    0.422840] 2800c000.uart: ttyAMA0 at MMIO 0x2800c000 (irq = 14, base_baud = 0) is a PL011 rev3
[    0.432002] 2800d000.uart: ttyAMA1 at MMIO 0x2800d000 (irq = 15, base_baud = 0) is a PL011 rev3
[    0.440797] printk: console [ttyAMA1] enabled
[    0.440797] printk: console [ttyAMA1] enabled
[    0.449533] printk: bootconsole [pl11] disabled
[    0.449533] printk: bootconsole [pl11] disabled
[    0.459020] 2800e000.uart: ttyAMA2 at MMIO 0x2800e000 (irq = 16, base_baud = 0) is a PL011 rev3
[    0.468042] 2800f000.uart: ttyAMA3 at MMIO 0x2800f000 (irq = 17, base_baud = 0) is a PL011 rev3
[    0.479156] Modules: 26240 pages in range for non-PLT usage
[    0.479160] Modules: 517760 pages in range for PLT usage
[    0.485105] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.497193] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[    0.503799] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[    0.510578] HugeTLB: 508 KiB vmemmap can be freed for a 32.0 MiB page
[    0.517010] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.523788] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[    0.530133] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[    0.536911] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[    0.544006] ACPI: Interpreter disabled.
[    0.548180] phytium-ddma 28003000.dma-controller: phytium DDMA Controller registered
[    0.556195] phytium-ddma 28004000.dma-controller: phytium DDMA Controller registered
[    0.564155] iommu: Default domain type: Translated
[    0.568945] iommu: DMA domain TLB invalidation policy: strict mode
[    0.575302] SCSI subsystem initialized
[    0.579256] usbcore: registered new interface driver usbfs
[    0.584747] usbcore: registered new interface driver hub
[    0.590068] usbcore: registered new device driver usb
[    0.595244] pps_core: LinuxPPS API ver. 1 registered
[    0.600202] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.609331] PTP clock support registered
[    0.613300] EDAC MC: Ver: 3.0.0
[    0.616646] scmi_core: SCMI protocol bus registered
[    0.621677] FPGA manager framework
[    0.625091] Advanced Linux Sound Architecture Driver Initialized.
[    0.631562] vgaarb: loaded
[    0.634425] clocksource: Switched to clocksource arch_sys_counter
[    0.640625] VFS: Disk quotas dquot_6.6.0
[    0.644557] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.651503] pnp: PnP ACPI: disabled
[    0.658282] NET: Registered PF_INET protocol family
[    0.663271] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.672141] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.680701] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.688446] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.696423] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[    0.704331] TCP: Hash tables configured (established 32768 bind 32768)
[    0.710916] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.717634] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.724843] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.730713] RPC: Registered named UNIX socket transport module.
[    0.736637] RPC: Registered udp transport module.
[    0.741337] RPC: Registered tcp transport module.
[    0.746034] RPC: Registered tcp-with-tls transport module.
[    0.751512] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.757948] PCI: CLS 0 bytes, default 64
[    0.761998] Unpacking initramfs...
[    0.765556] kvm [1]: KVM ncsnp disabled
[    0.769394] kvm [1]: KVM dvmbm disabled
[    0.773223] kvm [1]: IPA Size Limit: 40 bits
[    0.777994] kvm [1]: vgic-v2@30860000
[    0.781665] kvm [1]: GIC system register CPU interface enabled
[    0.787500] kvm [1]: vgic interrupt IRQ9
[    0.791430] kvm [1]: Hyp mode initialized successfully
[    0.797179] Initialise system trusted keyrings
[    0.801732] workingset: timestamp_bits=42 max_order=20 bucket_order=0
[    0.808318] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.814286] NFS: Registering the id_resolver key type
[    0.819348] Key type id_resolver registered
[    0.823525] Key type id_legacy registered
[    0.827534] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.834228] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.841958] SGI XFS with security attributes, no debug enabled
[    0.848073] 9p: Installing v9fs 9p2000 file system support
[    0.863895] Key type asymmetric registered
[    0.867988] Asymmetric key parser 'x509' registered
[    0.872890] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.880281] io scheduler mq-deadline registered
[    0.884804] io scheduler kyber registered
[    0.888825] io scheduler bfq registered
[    0.895398] gpio-phytium-platform 28034000.gpio: Phytium GPIO controller @0x0000000028034000 registered
[    0.906179] gpio-phytium-platform 28035000.gpio: Phytium GPIO controller @0x0000000028035000 registered
[    0.916944] gpio-phytium-platform 28036000.gpio: Phytium GPIO controller @0x0000000028036000 registered
[    0.926492] gpio-phytium-platform 28037000.gpio: Phytium GPIO controller @0x0000000028037000 registered
[    0.936042] gpio-phytium-platform 28038000.gpio: Phytium GPIO controller @0x0000000028038000 registered
[    0.945581] gpio-phytium-platform 28039000.gpio: Phytium GPIO controller @0x0000000028039000 registered
[    0.955333] pci-host-generic 40000000.pcie: host bridge /soc/pcie@40000000 ranges:
[    0.962920] pci-host-generic 40000000.pcie:       IO 0x0050000000..0x0050efffff -> 0x0000000000
[    0.971624] pci-host-generic 40000000.pcie:      MEM 0x0058000000..0x007fffffff -> 0x0058000000
[    0.974317] Freeing initrd memory: 8036K
[    0.980320] pci-host-generic 40000000.pcie:      MEM 0x1000000000..0x1fffffffff -> 0x1000000000
[    0.980351] pci-host-generic 40000000.pcie: Memory resource size exceeds max for 32 bits
[    1.001049] pci-host-generic 40000000.pcie: ECAM at [mem 0x40000000-0x4fffffff] for [bus 00-ff]
[    1.009884] pci-host-generic 40000000.pcie: PCI host bridge to bus 0000:00
[    1.016761] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.022241] pci_bus 0000:00: root bus resource [io  0x0000-0xefffff]
[    1.028587] pci_bus 0000:00: root bus resource [mem 0x58000000-0x7fffffff]
[    1.035455] pci_bus 0000:00: root bus resource [mem 0x1000000000-0x1fffffffff]
[    1.042713] pci 0000:00:01.0: [1db7:dc01] type 01 class 0x060400
[    1.048720] pci 0000:00:01.0: reg 0x10: [mem 0x1000000000-0x10000fffff 64bit pref]
[    1.056315] pci 0000:00:01.0: supports D1 D2
[    1.060579] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.067771] pci 0000:01:00.0: [168c:0036] type 00 class 0x028000
[    1.073798] pci 0000:01:00.0: reg 0x10: [mem 0x58000000-0x5807ffff 64bit]
[    1.080632] pci 0000:01:00.0: reg 0x30: [mem 0x58080000-0x5808ffff pref]
[    1.087406] pci 0000:01:00.0: supports D1 D2
[    1.091669] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.110448] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.117075] pci 0000:00:01.0: BAR 0: assigned [mem 0x1000000000-0x10000fffff 64bit pref]
[    1.125165] pci 0000:00:01.0: BAR 14: assigned [mem 0x58000000-0x581fffff]
[    1.132036] pci 0000:00:01.0: BAR 15: assigned [mem 0x1000100000-0x10002fffff 64bit pref]
[    1.140207] pci 0000:00:01.0: BAR 13: assigned [io  0x1000-0x1fff]
[    1.146383] pci 0000:01:00.0: BAR 0: assigned [mem 0x58000000-0x5807ffff 64bit]
[    1.153696] pci 0000:01:00.0: BAR 6: assigned [mem 0x58080000-0x5808ffff pref]
[    1.160912] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.165871] pci 0000:00:01.0:   bridge window [io  0x1000-0x1fff]
[    1.171960] pci 0000:00:01.0:   bridge window [mem 0x58000000-0x581fffff]
[    1.178741] pci 0000:00:01.0:   bridge window [mem 0x1000100000-0x10002fffff 64bit pref]
[    1.187269] EINJ: ACPI disabled.
[    1.192944] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.200536] random: crng init done
[    1.200664] arm-smmu-v3 30000000.iommu: ias 40-bit, oas 40-bit (features 0x00201faf)
[    1.211952] arm-smmu-v3 30000000.iommu: allocated 65536 entries for cmdq
[    1.218801] arm-smmu-v3 30000000.iommu: allocated 32768 entries for evtq
[    1.226486] arm-smmu-v3 30000000.iommu: msi_domain absent - falling back to wired irqs
[    1.237401] loop: module loaded
[    1.240875] megasas: 07.725.01.00-rc1
[    1.246497] tun: Universal TUN/TAP device driver, 1.6
[    1.586524] macb 3200c000.ethernet eth0: Cadence GEM rev 0x000c010d at 0x3200c000 irq 74 (24:dc:0f:18:15:c0)
[    1.930716] macb 3200e000.ethernet eth1: Cadence GEM rev 0x000c010d at 0x3200e000 irq 82 (24:dc:0f:18:15:c1)
[    1.940591] thunder_xcv, ver 1.0
[    1.943835] thunder_bgx, ver 1.0
[    1.947069] nicpf, ver 1.0
[    1.949940] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[    1.957158] hns3: Copyright (c) 2017 Huawei Corporation.
[    1.962500] hclge is initializing
[    1.965817] e1000: Intel(R) PRO/1000 Network Driver
[    1.970693] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    1.976447] e1000e: Intel(R) PRO/1000 Network Driver
[    1.981405] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.987330] igb: Intel(R) Gigabit Ethernet Network Driver
[    1.992722] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.998302] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[    2.004562] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    2.010524] sky2: driver version 1.30
[    2.014627] VFIO - User Level meta-driver version: 0.3
[    2.020375] xhci-hcd 31a08000.usb3: xHCI Host Controller
[    2.025692] xhci-hcd 31a08000.usb3: new USB bus registered, assigned bus number 1
[    2.033208] xhci-hcd 31a08000.usb3: hcc params 0x08007f0d hci version 0x110 quirks 0x0000000000000090
[    2.042443] xhci-hcd 31a08000.usb3: irq 86, io mem 0x31a08000
[    2.048272] xhci-hcd 31a08000.usb3: xHCI Host Controller
[    2.053582] xhci-hcd 31a08000.usb3: new USB bus registered, assigned bus number 2
[    2.061060] xhci-hcd 31a08000.usb3: Host supports USB 3.1 Enhanced SuperSpeed
[    2.068545] hub 1-0:1.0: USB hub found
[    2.072315] hub 1-0:1.0: 1 port detected
[    2.076433] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.084786] hub 2-0:1.0: USB hub found
[    2.088551] hub 2-0:1.0: 1 port detected
[    2.092725] xhci-hcd 31a28000.usb3: xHCI Host Controller
[    2.098042] xhci-hcd 31a28000.usb3: new USB bus registered, assigned bus number 3
[    2.105564] xhci-hcd 31a28000.usb3: hcc params 0x08007f0d hci version 0x110 quirks 0x0000000000000090
[    2.114797] xhci-hcd 31a28000.usb3: irq 87, io mem 0x31a28000
[    2.120622] xhci-hcd 31a28000.usb3: xHCI Host Controller
[    2.125931] xhci-hcd 31a28000.usb3: new USB bus registered, assigned bus number 4
[    2.133409] xhci-hcd 31a28000.usb3: Host supports USB 3.1 Enhanced SuperSpeed
[    2.140830] hub 3-0:1.0: USB hub found
[    2.144597] hub 3-0:1.0: 1 port detected
[    2.148703] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.157059] hub 4-0:1.0: USB hub found
[    2.160827] hub 4-0:1.0: 1 port detected
[    2.164953] usbcore: registered new interface driver usb-storage
[    2.171681] i2c_dev: i2c /dev entries driver
[    2.177435] sbsa-gwdt 28041000.watchdog: Initialized with 30s timeout @ 50000000 Hz, action=0.
[    2.186142] sbsa-gwdt 28043000.watchdog: Initialized with 30s timeout @ 50000000 Hz, action=0.
[    2.195166] sdhci: Secure Digital Host Controller Interface driver
[    2.201342] sdhci: Copyright(c) Pierre Ossman
[    2.205814] Synopsys Designware Multimedia Card Interface Driver
[    2.212046] phytium-mci-platform 28000000.mmc: mci clk set 0 0 0x0 0x0 0x0 0x0
[    2.219317] phytium-mci-platform 28000000.mmc: init hardware done!
[    2.250436] phytium-mci-platform 28000000.mmc: phytium_mci_probe 114: probe phytium mci successful.
[    2.259573] phytium-mci-platform 28001000.mmc: mci clk set 0 0 0x0 0x0 0x0 0x0
[    2.266851] phytium-mci-platform 28001000.mmc: init hardware done!
[    2.278032] phytium-mci-platform 28000000.mmc: card claims to support voltages below defined range
[    2.286989] phytium-mci-platform 28000000.mmc: no support for card's volts
[    2.293856] mmc0: error -22 whilst initialising SDIO card
[    2.298203] phytium-mci-platform 28001000.mmc: phytium_mci_probe 114: probe phytium mci successful.
[    2.308352] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.314592] ledtrig-cpu: registered to indicate activity on CPUs
[    2.319237] phytium-mci-platform 28001000.mmc: card claims to support voltages below defined range
[    2.320765] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    2.336198] usbcore: registered new interface driver usbhid
[    2.339165] mmc1: new high speed SDIO card at address 0001
[    2.341774] usbhid: USB HID core driver
[    2.351435] phytium-mbox 32a00000.mailbox: Phytium SoC Mailbox registered
[    2.358763] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    2.367470] es8336 1-0010: Can not get spk_ctl_gpio
[    2.372368] es8336 1-0010: Can not get hp_det_gpio
[    2.377757] NET: Registered PF_PACKET protocol family
[    2.382867] 9pnet: Installing 9P2000 support
[    2.387217] Key type dns_resolver registered
[    2.391486] mmc0: host does not support reading read-only switch, assuming write-enable
[    2.396564] registered taskstats version 1
[    2.401254] mmc0: new high speed SDHC card at address 0001
[    2.402447] usb 3-1: new full-speed USB device number 2 using xhci-hcd
[    2.403716] Loading compiled-in X.509 certificates
[    2.409364] mmcblk0: mmc0:0001 SD32G 29.1 GiB
[    2.425025] pcieport 0000:00:01.0: Adding to iommu group 0
[    2.430955] pcieport 0000:00:01.0: PME: Signaling with IRQ 99
[    2.436904]  mmcblk0: p1 p2 p3
[    2.436966] pcieport 0000:00:01.0: AER: enabled with IRQ 99
[    2.446269] scmi_protocol scmi_dev.1: Enabled polling mode TX channel - prot_id:16
[    2.453981] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    2.460734] arm-scmi firmware:scmi: SCMI Protocol v2.0 'Phytium:E2000' Firmware version 0x2050000
[    2.470531] cpu cpu0: EM: created perf domain
[    2.475691] cpu cpu2: EM: created perf domain
[    2.480596] cpu cpu3: EM: created perf domain
[    2.528952] genirq: irq_chip (null) did not update eff. affinity mask of irq 100
[    2.656837] input: phytium,pe220x-i2s-audio Headphones as /devices/platform/sound/sound/card0/input0
[    2.668160] of_cfs_init
[    2.670627] of_cfs_init: OK
[    2.673514] clk: Disabling unused clocks
[    2.677444] ALSA device list:
[    2.680406]   #0: phytium,pe220x-i2s-audio
[    2.684567] uart-pl011 2800d000.uart: no DMA platform data
[    2.691051] Freeing unused kernel memory: 3200K
[    2.695646] Run /init as init process
Loading, please wait...
Starting version 249.11-0ubuntu3.12
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.37.2
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p3] fsck.ext4 -y -C0 /dev/mmcblk0p3
e2fsck 1.46.5 (30-Dec-2021)
/dev/mmcblk0p3: clean, 21791/100464 files, 248023/401408 blocks
done.
[    3.667354] EXT4-fs (mmcblk0p3): mounted filesystem a8831aa1-6628-4426-9ca7-ee808e243549 r/w with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    4.733221] NET: Registered PF_INET6 protocol family
[    4.740498] Segment Routing with IPv6
[    4.744335] In-situ OAM (IOAM) with IPv6
[    4.849249] systemd[1]: systemd v255-17.oe2403 running in system mode (+PAM +AUDIT +SELINUX -APPARMOR +IMA -SMACK +SECCOMP +GCRYPT +GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE -TPM2 +BZIP2 +LZ4 +XZ +ZLIB -ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=legacy)
[    4.882001] systemd[1]: Detected architecture arm64.

Welcome to openEuler 24.03 (LTS)!

[    4.953302] systemd[1]: Hostname set to <openEuler>.
[    5.187587] systemd-sysv-generator[179]: SysV service '/etc/rc.d/init.d/extend-root.sh' lacks a native systemd unit file.  Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it safe, robust and future-proof.  This compatibility logic is deprecated, expect removal soon. 
[    5.488723] systemd[1]: /usr/lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
[    5.692430] systemd[1]: Queued start job for default target Graphical Interface.
[    5.763470] systemd[1]: Created slice Slice /system/getty.
[  OK  ] Created slice Slice /system/getty.
[    5.784135] systemd[1]: Created slice Slice /system/modprobe.
[  OK  ] Created slice Slice /system/modprobe.
[    5.804060] systemd[1]: Created slice Slice /system/serial-getty.
[  OK  ] Created slice Slice /system/serial-getty.
[    5.828124] systemd[1]: Created slice Slice /system/sshd-keygen.
[  OK  ] Created slice Slice /system/sshd-keygen.
[    5.851802] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[    5.870831] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password Requests to Console Directory Watch.
[    5.894768] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password Requests to Wall Directory Watch.
[    5.918674] systemd[1]: Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc).
[    5.935089] systemd[1]: Reached target Local Encrypted Volumes.
[  OK  ] Reached target Local Encrypted Volumes.
[    5.954626] systemd[1]: Reached target Local Integrity Protected Volumes.
[  OK  ] Reached target Local Integrity Protected Volumes.
[    5.978651] systemd[1]: Reached target Path Units.
[  OK  ] Reached target Path Units.
[    5.994601] systemd[1]: Reached target Remote Encrypted Volumes.
[  OK  ] Reached target Remote Encrypted Volumes.
[    6.014609] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    6.034656] systemd[1]: Reached target Slice Units.
[  OK  ] Reached target Slice Units.
[    6.054773] systemd[1]: Reached target Local Verity Protected Volumes.
[  OK  ] Reached target Local Verity Protected Volumes.
[    6.084606] systemd[1]: Listening on Process Core Dump Socket.
[  OK  ] Listening on Process Core Dump Socket.
[    6.107021] systemd[1]: Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on initctl Compatibility Named Pipe.
[    6.127398] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    6.147397] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    6.168608] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    6.187296] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[    6.230690] systemd[1]: Mounting Huge Pages File System...
         Mounting Huge Pages File System...
[    6.266750] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[    6.298905] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[    6.323165] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[    6.340006] systemd[1]: Starting Create List of Static Device Nodes...
         Starting Create List of Static Device Nodes...
[    6.392839] systemd[1]: Starting Load Kernel Module configfs...
         Starting Load Kernel Module configfs...
[    6.419980] systemd[1]: Starting Load Kernel Module drm...
         Starting Load Kernel Module drm...
[    6.446599] systemd[1]: Starting Load Kernel Module fuse...
         Starting Load Kernel Module fuse...
[    6.471399] systemd[1]: systemd-journald.service: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[    6.484337] systemd[1]: systemd-journald.service: (This warning is only shown for the first unit using IP firewalling.)
[    6.499419] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[    6.550160] fuse: init (API version 7.39)
[    6.559738] systemd[1]: Load Kernel Modules was skipped because no trigger condition checks were met.
[    6.595079] systemd[1]: Starting Generate network units from Kernel command line...
         Starting Generate network units from Kernel command line...
[    6.622011] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[    6.649725] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[    6.669911] systemd[1]: Starting Coldplug All udev Devices...
         Starting Coldplug All udev Devices...
[    6.695373] systemd[1]: Mounted Huge Pages File System.
[  OK  ] Mounted Huge Pages File System.
[    6.708159] systemd-journald[196]: Collecting audit messages is disabled.
[    6.716541] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[    6.739467] systemd[1]: Mounted Kernel Debug File System.
[    6.742721] EXT4-fs (mmcblk0p3): re-mounted a8831aa1-6628-4426-9ca7-ee808e243549 r/w. Quota mode: none.
[  OK  ] Mounted Kernel Debug File System.
[    6.774015] systemd[1]: Finished Create List of Static Device Nodes.
[  OK  ] Finished Create List of Static Device Nodes.
[    6.795324] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
[  OK  ] Finished Load Kernel Module configfs.
[  OK  ] Finished Load Kernel Module drm.
[  OK  ] Finished Load Kernel Module fuse.
[  OK  ] Finished Generate network units from Kernel command line.
[  OK  ] Finished Remount Root and Kernel File Systems.
[  OK  ] Finished Apply Kernel Variables.
[  OK  ] Reached target Preparation for Network.
         Mounting FUSE Control File System...
         Mounting Kernel Configuration File System...
         Starting Rebuild Hardware Database...
         Starting Flush Journal to Persistent Storage...
         Starting Load/Save OS Random Seed...
         Starting Create Static Device Nodes in /dev gracefully...
[  OK  ] Finished Coldplug All udev Devices.
[  OK  ] Mounted FUSE Control File System.
[  OK  ] Mounted Kernel Configuration File System.
[    7.174292] systemd-journald[196]: Received client request to flush runtime journal.
[  OK  ] Finished Flush Journal to Persistent Storage.
[  OK  ] Finished Load/Save OS Random Seed.
[  OK  ] Finished Create Static Device Nodes in /dev gracefully.
         Starting Create System Users...
[  OK  ] Finished Create System Users.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Finished Create Static Device Nodes in /dev.
[  OK  ] Reached target Preparation for Local File Systems.
[  OK  ] Finished Rebuild Hardware Database.
         Starting Rule-based Manager for Device Events and Files...
[  OK  ] Started Rule-based Manager for Device Events and Files.
[  OK  ] Found device /dev/ttyAMA1.
[  OK  ] Found device /dev/disk/by-partuuid/16609bf9-02.
[   10.128817] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[   10.136032] phytium-qspi 28008000.spi: Flash size is invalid.
[   10.141933] phytium-qspi: probe of 28008000.spi failed with error -22
         Activating swap /dev/disk/by-partuuid/16609bf9-02...
[   10.224219] phytium-otg 31800000.usb2: Phytium Host USB Driver
[   10.231708] phytium-otg 31800000.usb2: new USB bus registered, assigned bus number 5
[   10.243594] hub 5-0:1.0: USB hub found
[   10.248508] hub 5-0:1.0: 1 port detected
[   10.254670] phytium-otg 32800000.usb2: Phytium Host USB Driver
[   10.260632] phytium-otg 32800000.usb2: new USB bus registered, assigned bus number 6
[   10.270597] hub 6-0:1.0: USB hub found
[   10.275342] hub 6-0:1.0: 1 port detected
[   10.281166] phytium-otg 32840000.usb2: Phytium Host USB Driver
[   10.287019] phytium-otg 32840000.usb2: new USB bus registered, assigned bus number 7
[   10.302890] hub 7-0:1.0: USB hub found
[   10.306666] hub 7-0:1.0: 1 port detected
[  OK  ] Found device /dev/disk/by-partuuid/16609bf9-01.
[   10.335609] CAN device driver interface
         Mounting /boot...
[   10.504744] phytium_can_platform 2800a000.can: phytium_can device registered (irq=105)
[   10.513836] phytium_can_platform 2800b000.can: phytium_can device registered (irq=106)
[   10.583889] Adding 499708k swap on /dev/mmcblk0p2.  Priority:-2 extents:1 across:499708k SS
[   10.669151] phytium_display_platform 32000000.dc: [drm] Cannot find any crtc or sizes
[   10.677136] [drm] Initialized dc 1.1.0 20201220 for 32000000.dc on minor 0
[   10.685057] input: PMDK-I2S HDMI/DP,pcm=0 as /devices/platform/soc/soc:pmdk_dp/sound/card1/input1
[   10.740744] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   10.768943] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   10.775370] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[  OK  ] Activated swap /dev/disk/by-partuuid/16609bf9-02.
[  OK  ] Reached target Swaps.
         Mounting Temporary Directory /tmp...
         Starting Virtual Console Setup...
[  OK  ] Mounted Temporary Directory /tmp.
[   10.973393] Bluetooth: Core ver 2.22
[   10.977109] NET: Registered PF_BLUETOOTH protocol family
[   10.982863] Bluetooth: HCI device and connection manager initialized
[   10.989475] Bluetooth: HCI socket layer initialized
[   10.994492] Bluetooth: L2CAP socket layer initialized
[   10.999738] Bluetooth: SCO socket layer initialized
[   11.335696] usbcore: registered new interface driver btusb
[  OK  ] Mounted /boot.
[  OK  ] Reached target Local 
         Starting Rebuild Dynamic Linker Cache...
         Starting Create Volatile Files and Directories...
[  OK  ] Finished Virtual Console Setup.
[  OK  ] Finished Create Volatile Files and Directories.
         Starting Rebuild Journal Catalog...
         Starting Network Time Synchronization...
         Starting Record System Boot/Shutdown in UTMP...
[  OK  ] Finished Record System Boot/Shutdown in UTMP.
[  OK  ] Finished Rebuild Journal Catalog.
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Set.
[  OK  ] Finished Rebuild Dynamic Linker Cache.
         Starting Update is Completed...
[  OK  ] Finished Update is Completed.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timer Units.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Socket Units.
[  OK  ] Reached target Basic System.
[  OK  ] Started Manage Sound Card State (restore and store).
[  OK  ] Reached target Sound Card.
         Starting D-Bus System Message Bus...
         Starting Restore /run/initramfs on shutdown...
         Starting SYSV: extend root...
[  OK  ] Started Entropy Daemon based on the HAVEGE algorithm.
         Starting Update RTC With System Clock...
         Starting Authorization Manager...
         Starting RealtimeKit Scheduling Policy Service...
         Starting OpenSSH ecdsa Server Key Generation...
         Starting OpenSSH ed25519 Server Key Generation...
         Starting OpenSSH rsa Server Key Generation...
         Starting User Login Management...
[  OK  ] Finished Restore /run/initramfs on shutdown.
[  OK  ] Finished Update RTC With System Clock.
[  OK  ] Started User Login Management.
[  OK  ] Started D-Bus System Message Bus.
         Starting Network Manager...
[  OK  ] Started RealtimeKit Scheduling Policy Service.
[  OK  ] Finished OpenSSH ecdsa Server Key Generation.
[  OK  ] Finished OpenSSH ed25519 Server Key Generation.
[  OK  ] Started Authorization Manager.
         Starting Modem Manager...
[   15.805841] EXT4-fs (mmcblk0p3): resizing filesystem from 401408 to 7440896 blocks
         Starting Hostname Service...
[  OK  ] Started Hostname Service.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Started Modem Manager.
[  OK  ] Started    16.522835] macb 3200c000.ethernet eth0: PHY [3200c000.ethernet-ffffffff:00] driver [YT8521 Gigabit Ethernet] (irq=POLL)
;39mNetwork Manager Script Dispa[   16.536441] macb 3200c000.ethernet eth0: configuring for phy/sgmii link mode
tcher Service.
[   16.547087] pps pps0: new PPS source ptp0
[   16.554685] macb 3200c000.ethernet: gem-ptp-timer ptp clock registered.
[   16.593660] macb 3200e000.ethernet eth1: PHY [3200e000.ethernet-ffffffff:00] driver [YT8521 Gigabit Ethernet] (irq=POLL)
[   16.604687] macb 3200e000.ethernet eth1: configuring for phy/sgmii link mode
[   16.612765] pps pps1: new PPS source ptp1
[   16.616972] macb 3200e000.ethernet: gem-ptp-timer ptp clock registered.
[  OK  ] Started Network Manager.
[  OK  ] Reached target Network.
         Starting /etc/rc.d/rc.local Compatibility...
         Starting Permit User Sessions...
[  OK  ] Started /etc/rc.d/rc.local Compatibility.
[  OK  ] Finished Permit User Sessions.
[  OK  ] Started Command Scheduler.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttyAMA1.
[   16.928699] EXT4-fs (mmcblk0p3): resized filesystem to 7440896
[  OK  ] Reached target Login Prompts.
[  OK  ] Started SYSV: extend root.
[  OK  ] Finished OpenSSH rsa Server Key Generation.
[  OK  ] Reached target sshd-keygen.target.
         Starting OpenSSH server daemon...
[  OK  ] Started OpenSSH server daemon.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Record Runlevel Change in UTMP...
[   19.623305] macb 3200c000.ethernet eth0: unable to generate target frequency: 125000000 Hz
[  OK  ] Finished Record Runlevel Change in UTMP.
[   19.637211] macb 3200c000.ethernet eth0: unable to generate target frequency: 125000000 Hz
[   19.646653] macb 3200c000.ethernet eth0: Link is Up - 1Gbps/Full - flow control tx

openEuler 24.03 (LTS)
Kernel 6.6.0-phytium-embedded-v3.0+ on an aarch64

openEuler login: [   21.606951] amba 28014000.uart: deferred probe pending
[   21.612138] amba 2802a000.uart: deferred probe pending
[   21.617329] amba 28032000.uart: deferred probe pending

openEuler login: root
Password:

Welcome to 6.6.0-phytium-embedded-v3.0+

System information as of time:  Thu Jan  1 08:00:30 AM CST 1970

System load:    2.47
Memory used:    2.6%
Swap used:      0%
Usage On:       4%
IP address:     192.168.8.229
Users online:   1

[root@openEuler ~]#
```

类型	指派人员	状态
审查	openeuler-ci-bot	已完成 (0/0人)
测试	openeuler-ci-bot	已完成 (0/0人)

openEuler/phytium-kernel .gitee-modal { width: 500px !important; }

搜索帮助

openEuler/phytium-kernel