# recomputer **Repository Path**: qqdyta/recomputer ## Basic Information - **Project Name**: recomputer - **Description**: No description available - **Primary Language**: Unknown - **License**: MIT - **Default Branch**: master - **Homepage**: None - **GVP Project**: No ## Statistics - **Stars**: 0 - **Forks**: 0 - **Created**: 2024-06-17 - **Last Updated**: 2024-07-03 ## Categories & Tags **Categories**: Uncategorized **Tags**: None ## README # AM67 定频测试脚本使用指南 ## 1. 开机进入系统 1. 测试设备的用户名为 `debian`，密码为 `000000`。 2. 通过终端登录系统后，首先运行以下命令以克隆测试脚本仓库： ```sh git clone https://github.com/qqdyta/am67_rf.git ``` 3. 进入测试脚本目录： ```sh cd am67_rf ``` ## 2. 文件夹说明测试脚本目录包含以下子文件夹，每个文件夹对应不同的测试类型： - `wifi5g_tx`: 用于测试 5 GHz 频段下的调制波测试 - `wifi5g_tune`: 用于测试 5 GHz 频段下的单载波测试 - `wifi2g_tx`: 用于测试 2.4 GHz 频段下的调制波测试 - `wifi2g_tune`: 用于测试 2.4 GHz 频段下的单载波测试 ## 3. 测试准备 1. 执行以下命令以进入超级管理员模式： ```sh sudo su ``` 输入密码 `000000`。 2. 进入对应的测试目录，例如： ```sh cd wifi2g_tx ``` ## 4. 执行测试脚本每次执行测试脚本前，请确保以下几点： 1. **进入对应的测试目录**，如 `wifi2g_tx` 或 `wifi5g_tune`。 2. **执行测试脚本**，例如： ```sh sh your_test_script.sh ``` 3. **停止测试**：每次执行完一个测试脚本后，必须运行相应的停止脚本以停止当前测试，然后才能开始下一个波段的测试： ```sh sh stop.sh ``` ## 5. 注意事项 - **超级管理员权限**：执行测试脚本前，确保已经进入超级管理员模式。 - **停止脚本**：每次执行完一个测试脚本后，务必运行 `stop.sh` 脚本停止当前测试，避免对下一个测试波段产生影响。 - **测试目录**：确保在正确的测试目录下运行脚本，以免测试结果不准确或脚本无法执行。感谢使用 AM67 定频测试脚本。如有问题，请参考脚本仓库中的其他文档或联系支持团队。试 # WL 使用指南 Usage: ./wl [-a|i ] [-h] [-d|u|x] [-w|--wlc ] [arguments] -h this message and command descriptions -h [cmd] command description for cmd -a, -i adapter name or number -d output format signed integer -u output format unsigned integer -x output format hexdecimal -w index of WLC for RSDB only ver get version information cmds generate a short list of available commands up reinitialize and mark adapter up (operational) down reset and mark adapter down (disabled) out mark adapter down but do not reset hardware(disabled) On dualband cards, cards must be bandlocked before use. clk set board clock state. return error for set_clk attempt if the driver is not down 0: clock off 1: clock on restart Restart driver. Driver must already be down. reboot Reboot platform radio Set the radio on or off. "on" or "off" dump Give suboption "list" to list various suboptions ol_stats Give suboption "list" to list various suboptions ol_eventlog Give suboption "list" to list various suboptions ol_cons Display the ARM console or issue a command to the ARM console Usage: ol_cons [] "?" - Display the list of active console commands ol_wowl_cons Give suboption "list" to list various suboptions ol_clr Give suboption "list" to list various suboptions srclear Clears first 'len' bytes of the srom, len in decimal or hex Usage: srclear srdump print contents of SPROM to stdout srwrite Write the srom: srwrite byteoffset value srcrc Get the CRC for input binary file ciswrite Write specified to the SDIO CIS source (either SROM or OTP) cisupdate Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP) --preview option allows you to review the update without committing it [--preview] cisdump Display the content of the SDIO CIS source -b -- also write raw bytes to -- optional count of bytes to display (must be even) cis_source Display which source is used for the SDIO CIS cisconvert Print CIS tuple for given name=value pair rdvar Read a named variable to the srom wrvar Write a named variable to the srom nvram_source Display which source is used for nvram nvram_dump print nvram variables to stdout nvset set an nvram variable name=value (no spaces around '=') nvget get the value of an nvram variable nvram_get get the value of an nvram variable revinfo get hardware revision information customvar1 print the value of customvar1 in hex format msglevel set driver console debugging message bitvector type 'wl msglevel ?' for values phymsglevel set phy debugging message bitvector type 'wl phymsglevel ?' for values PM set driver power management mode: 0: CAM (constantly awake) 1: PS (power-save) 2: FAST PS mode wake set driver power-save mode sleep state: 0: core-managed 1: awake promisc set promiscuous mode ethernet address reception 0 - disable 1 - enable monitor set monitor mode 0 - disable 1 - enable active monitor mode (interface still operates) frag Deprecated. Use fragthresh. rts Deprecated. Use rtsthresh. cwmin Set the cwmin. (integer [1, 255]) cwmax Set the cwmax. (integer [256, 2047]) srl Set the short retry limit. (integer [1, 255]) lrl Set the long retry limit. (integer [1, 255]) rate force a fixed rate: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate mrate force a fixed multicast rate: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate a_rate force a fixed rate for the A PHY: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate a_mrate force a fixed multicast rate for the A PHY: valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate bg_rate force a fixed rate for the B/G PHY: valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate bg_mrate force a fixed multicast rate for the B/G PHY: valid values for 802.11b are (1, 2, 5.5, 11) valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54) -1 (default) means automatically determine the best rate 2g_rate Force a fixed rate for data frames in the 2.4G band: Either "auto", or a simple CCK/DSSS/OFDM rate value: 1 2 5.5 11 6 9 12 18 24 36 48 54 Or options to specify legacy, HT, or VHT rate: -r R, --rate=R : legacy rate (CCK, DSSS, OFDM) -h M, --ht=M : HT MCS index [0-23] -v M[xS], --vht=M[xS] : VHT MCS index M [0-9], : and optionally Nss S [1-8], eg. 5x2 is MCS=5, Nss=2 -c cM[sS] : VHT (c notation) MCS index M [0-9], : and optionally Nss S [1-8], eg. c5s2 is MCS=5, Nss=2 -s S, --ss=S : VHT Nss [1-8], number of spatial streams, default 1. : Only used with -v/--vht when MxS format is not used -x T, --exp=T : Tx Expansion, number of tx chains (NTx) beyond the minimum : required for the space-time-streams, exp = NTx - Nsts --stbc : Use STBC expansion, otherwise no STBC -l, --ldpc : Use LDPC encoding, otherwise no LDPC -g, --sgi : SGI, Short Guard Interval, otherwise standard GI -b, --bandwidth : transmit bandwidth MHz; 20, 40, 80 2g_mrate Force a fixed rate for mulitcast/broadcast data frames in the 2.4G band: Either "auto", or a simple CCK/DSSS/OFDM rate value: 1 2 5.5 11 6 9 12 18 24 36 48 54 Or options to specify legacy, HT, or VHT rate: -r R, --rate=R : legacy rate (CCK, DSSS, OFDM) -h M, --ht=M : HT MCS index [0-23] -v M[xS], --vht=M[xS] : VHT MCS index M [0-9], : and optionally Nss S [1-8], eg. 5x2 is MCS=5, Nss=2 -c cM[sS] : VHT (c notation) MCS index M [0-9], : and optionally Nss S [1-8], eg. c5s2 is MCS=5, Nss=2 -s S, --ss=S : VHT Nss [1-8], number of spatial streams, default 1. : Only used with -v/--vht when MxS format is not used -x T, --exp=T : Tx Expansion, number of tx chains (NTx) beyond the minimum : required for the space-time-streams, exp = NTx - Nsts --stbc : Use STBC expansion, otherwise no STBC -l, --ldpc : Use LDPC encoding, otherwise no LDPC -g, --sgi : SGI, Short Guard Interval, otherwise standard GI -b, --bandwidth : transmit bandwidth MHz; 20, 40, 80 5g_rate Force a fixed rate for data frames in the 5G band: Either "auto", or a simple OFDM rate value: 6 9 12 18 24 36 48 54 Or options to specify legacy OFDM, HT, or VHT rate: -r R, --rate=R : legacy OFDM rate -h M, --ht=M : HT MCS index [0-23] -v M[xS], --vht=M[xS] : VHT MCS index M [0-9], : and optionally Nss S [1-8], eg. 5x2 is MCS=5, Nss=2 -c cM[sS] : VHT (c notation) MCS index M [0-9], : and optionally Nss S [1-8], eg. c5s2 is MCS=5, Nss=2 -s S, --ss=S : VHT Nss [1-8], number of spatial streams, default 1. : Only used with -v/--vht when MxS format is not used -x T, --exp=T : Tx Expansion, number of tx chains (NTx) beyond the minimum : required for the space-time-streams, exp = NTx - Nsts --stbc : Use STBC expansion, otherwise no STBC -l, --ldpc : Use LDPC encoding, otherwise no LDPC -g, --sgi : SGI, Short Guard Interval, otherwise standard GI -b, --bandwidth : transmit bandwidth MHz; 20, 40, 80 5g_mrate Force a fixed rate for mulitcast/broadcast data frames in the 5G band: Either "auto", or a simple OFDM rate value: 6 9 12 18 24 36 48 54 Or options to specify legacy OFDM, HT, or VHT rate: -r R, --rate=R : legacy OFDM rate -h M, --ht=M : HT MCS index [0-23] -v M[xS], --vht=M[xS] : VHT MCS index M [0-9], : and optionally Nss S [1-8], eg. 5x2 is MCS=5, Nss=2 -c cM[sS] : VHT (c notation) MCS index M [0-9], : and optionally Nss S [1-8], eg. c5s2 is MCS=5, Nss=2 -s S, --ss=S : VHT Nss [1-8], number of spatial streams, default 1. : Only used with -v/--vht when MxS format is not used -x T, --exp=T : Tx Expansion, number of tx chains (NTx) beyond the minimum : required for the space-time-streams, exp = NTx - Nsts --stbc : Use STBC expansion, otherwise no STBC -l, --ldpc : Use LDPC encoding, otherwise no LDPC -g, --sgi : SGI, Short Guard Interval, otherwise standard GI -b, --bandwidth : transmit bandwidth MHz; 20, 40, 80 infra Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS) ap Set AP mode: 0 (STA) or 1 (AP) bssid Get the BSSID value, error if STA and not associated bssmax get number of BSSes bw_cap Get/set the per-band bandwidth. Usage: wl bw_cap <2g|5g> [] 2g|5g - Band: 2.4GHz or 5GHz respectively cap: 0x1 - 20MHz 0x3 - 20/40MHz 0x7 - 20/40/80MHz 0xff - Unrestricted channel Set the channel: valid channels for 802.11b/g (2.4GHz band) are 1 through 14 valid channels for 802.11a (5 GHz band) are: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 184, 188, 192, 196, 200, 204, 208, 212, 216 cur_mcsset Get the current mcs set clmver Get version information for CLM data and tools roam_channels_in_cache Get a list of channels in roam cache roam_channels_in_hotlist Get a list of channels in roam hot channel list chanspecs Get all the valid chanspecs (default: all within current locale): -b band (5(a) or 2(b/g)) -w bandwidth, 20, 40 or 80 [-c country_abbrev] chanspecs_defset Get default chanspecs for current driver settings (default: all within current locale) chanspec Set current or configured channel: 20MHz : [2g|5g][/20] 40MHz : [2g|5g]/40[u,l] 80MHz : [5g]/80 optional band 2g or 5g, default to 2g if channel <= 14 channel number (0-200) bandwidth, 20, 40, or 80, default 20 primary sideband for 40MHz on 2g, l=lower, u=upper OR Set channel with legacy format: -c channel number (0-224) -b band (5(a) or 2(b/g)) -w bandwidth 20 or 40 -s ctl sideband, -1=lower, 0=none, 1=upper rclass Get operation class: chanspec dfs_channel_forced Set [a,b][n][u,l] channel number (0-224) band a=5G, b=2G, default to 2G if channel <= 14 bandwidth, n=10, non for 20 & 40 ctl sideband, l=lower, u=upper tssi Get the tssi value from radio txpwr Set tx power in milliwatts. Range [1, 84]. txpwr1 Set tx power in in various units. Choose one of (default: dbm): -d dbm units -q quarter dbm units -m milliwatt units Can be combined with: -o turn on override to disable regulatory and other limitations Use wl txpwr -1 to restore defaults txpathpwr Turn the tx path power on or off on 2050 radios txpwrlimit Return current tx power limit powerindex Set the transmit power for A band(0-63). -1 - default value atten Set the transmit attenuation for B band. Args: bb radio txctl1. auto to revert to automatic control manual to supspend automatic control phyreg Get/Set a phy register: offset [ value ] [ band ] radioreg Get/Set a radio register: offset [ value ] [ band/core ] HTPHY: Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2 ] Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/all ] ACPHY: Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2/pll ] Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/pll/all ] ucflags Get/Set ucode flags 1, 2, 3(16 bits each) offset [ value ] [ band ] shmem Get/Set a shared memory location: offset [ value ] [band ] macreg Get/Set any mac registers(include IHR and SB): macreg offset size[2,4] [ value ] [ band ] ucantdiv Enable/disable ucode antenna diversity (1/0 or on/off) gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon Usage: gpiomask gpioval devpath print device path pcieserdesreg g/set SERDES registers: dev offset [val] ampdu_activate_test actiate ampdu_tid enable/disable per-tid ampdu; usage: wl ampdu_tid [0/1] ampdu_retry_limit_tid Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid [0~31] ampdu_rr_retry_limit_tid Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid [0~31] ampdu_send_addba send addba to specified ea-tid; usage: wl ampdu_send_addba ampdu_send_delba send delba to specified ea-tid; usage: wl ampdu_send_delba ampdu_clear_dump clear ampdu counters ampdu_txq_prof_start start sample txq profiling data ampdu_txq_prof_dump show txq histogram ampdu_txq_ss take txq snapshot dpt_deny adds/removes ea to dpt deny list usage: wl dpt_deny dpt_endpoint creates/updates/deletes dpt endpoint for ea usage: wl dpt_endpoint dpt_pmk sets DPT pre-shared key dpt_fname sets/gets DPT friendly name dpt_list gets status of all dpt peers HCI_cmd carries HCI commands to the driver usage: wl HCI_cmd HCI_ACL_data carries HCI ACL data packet to the driver usage: wl HCI_ACL_data btamp_statelog Return state transistion log of BTAMP actframe Send a Vendor specific Action frame to a channel usage: wl actframe channel dwell-time antdiv Set antenna diversity for rx 0 - force use of antenna 0 1 - force use of antenna 1 3 - automatic selection of antenna diversity txant Set the transmit antenna 0 - force use of antenna 0 1 - force use of antenna 1 3 - use the RX antenna selection that was in force during the most recently received good PLCP header plcphdr Set the plcp header. "long" or "auto" or "debug" phytype Get phy type rateparam set driver rate selection tunables arg 1: tunable id arg 2: tunable value wepstatus Set or Get WEP status wepstatus [on|off] primary_key Set or get index of primary key addwep Set an encryption key. The key must be 5, 13 or 16 bytes long, or 10, 26, 32, or 64 hex digits long. The encryption algorithm is automatically selected based on the key size. keytype is accepted only when key length is 16 bytes/32 hex digits and specifies whether AES-OCB or AES-CCM encryption is used. Default is ccm. WAPI is selected if key len is 32 and arguments contain wapi. addwep [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx] rmwep Remove the encryption key at the specified key index. keys Prints a list of the current WEP keys tsc Print Tx Sequence Couter for key at specified key index. wsec_test Generate wsec errors wsec_test type 'wl wsec_test ?' for test_types tkip_countermeasures Enable or disable TKIP countermeasures (TKIP-enabled AP only) 0 - disable 1 - enable wsec_restrict Drop unencrypted packets if WSEC is enabled 0 - disable 1 - enable eap restrict traffic to 802.1X packets until 802.1X authorization succeeds 0 - disable 1 - enable cur_etheraddr Get/set the current hw address perm_etheraddr Get the permanent address from NVRAM authorize restrict traffic to 802.1X packets until 802.1X authorization succeeds deauthorize do not restrict traffic to 802.1X packets until 802.1X authorization succeeds deauthenticate deauthenticate a STA from the AP with optional reason code (AP ONLY) wsec wireless security bit vector 1 - WEP enabled 2 - TKIP enabled 4 - AES enabled 8 - WSEC in software 0x80 - FIPS enabled 0x100 - WAPI enabled 0x200 - MFP capable 0x400 - MFP required 0x800 - MFP use KDF (SHA256) auth set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 3=Open/Shared wpa_auth Bitvector of WPA authorization modes: 1 WPA-NONE 2 WPA-802.1X/WPA-Professional 4 WPA-PSK/WPA-Personal 64 WPA2-802.1X/WPA2-Professional 128 WPA2-PSK/WPA2-Personal 0 disable WPA wpa_cap set/get 802.11i RSN capabilities set_pmk Set passphrase for PMK in driver-resident supplicant. scan Initiate a scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan roamscan_parms set/get roam scan parameters Use standard scan params syntax below,but only active/passive/home times, nprobes, and type are used. All other values are silently discarded. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan iscan_s Initiate an incremental scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan iscan_c Continue an incremental scan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan scancache_clear clear the scan cache escan Start an escan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan escanabort Abort an escan. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan passive Puts scan engine into passive mode regulatory Get/Set regulatory domain mode (802.11d). Driver must be down. spect Get/Set 802.11h Spectrum Management mode. 0 - Off 1 - Loose interpretation of 11h spec - may join non-11h APs 2 - Strict interpretation of 11h spec - may not join non-11h APs 3 - Disable 11h and enable 11d 4 - Loose interpretation of 11h+d spec - may join non-11h APs scanabort Abort a scan. scanresults Return results from last scan. iscanresults Return results from last iscan. Specify a buflen (max 8188) to artificially limit the size of the results buffer. iscanresults [buflen] assoc Print information about current network association. (also known as "status") status Print information about current network association. (also known as "assoc") disassoc Disassociate from the current BSS/IBSS. chanlist Deprecated. Use channels. channels Return valid channels for the current settings. channels_in_country Return valid channels for the country specified. Arg 1 is the country abbreviation Arg 2 is the band(a or b) curpower Return current tx power settings. -v, --verbose: display the power settings for every rate even when every rate in a rate group has the same power. txpwr_target_max Return current max tx target power settings. curppr Return current tx power per rate offset. txinstpwr Return tx power based on instant TSSI scansuppress Suppress all scans for testing. 0 - allow scans 1 - suppress scans evm Start an EVM test on the given channel, or stop EVM test. Arg 1 is channel number 1-14, or "off" or 0 to stop the test. Arg 2 is optional rate (1, 2, 5.5 or 11) rateset Returns or sets the supported and basic rateset, (b) indicates basic With no args, returns the rateset. Args are rateset "default" | "all" | [-m|-v ] default - driver defaults all - all rates are basic rates arbitrary rateset - list of rates List of rates are in Mbps and each rate is optionally followed by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11 At least one rate must be Basic for a legal rateset. -m sets HT rates (bitmasks, 00-ff). Least significant bit is MCS0. example: 'rateset -m 0x3f 0x01' limits rates to MCS0-MCS5 and MCS8 -v sets VHT MCS values for each supported count of spatial streams. example: 'rateset -v 3ff 1ff ff' limits vht rates to MCS 0-9 for 1 stream, MCS 0-8 for 2 streams, and MCS 0-7 for 3 streams. default_rateset Returns supported rateset of given phy. You have to insert following Args Arg 1. Phy Type: have to be one of the following: [a, b, g, n, lp, ssn, ht, lcn, lcn40, ac] Arg 2. Band Type: 2 for 2.4G or 5 for 5G Arg 3. CCK Only: 1 for CCK Only or 0 for CCK and OFDM rates Arg 4. Basic Rates: 1 for all rates WITH basic rates or 0 for all rates WITHOUT basic rates Arg 5. MCS Rates: 1 for all rates WITH MCS rates or 0 for all rates WITHOUT MCS rates Arg 6. Bandwidth: have to be one of the following: [10, 20, 40, 80, 160] Arg 7. TX/RX Stream: "tx" for TX streams or "rx" for RX streams Example: PHY: AC, Band 2.4G, CCK rates only, With Basec rates, WithOut MCS rates, BW: 40 and TX streams Input: default_rateset ac 2 0 1 0 40 tx roam_trigger Get or Set the roam trigger RSSI threshold: Get: roam_trigger [a|b] Set: roam_trigger [a|b|all] integer - 0: default 1: optimize bandwidth 2: optimize distance [-1, -99]: dBm trigger value roam_delta Set the roam candidate qualification delta. roam_delta [integer [, a/b]] roam_scan_period Set the roam candidate qualification delta. (integer) suprates Returns or sets the 11g override for the supported rateset With no args, returns the rateset. Args are a list of rates, or 0 or -1 to specify an empty rateset to clear the override. List of rates are in Mbps, example: 1 2 5.5 11 scan_channel_time Get/Set scan channel time scan_unassoc_time Get/Set unassociated scan channel dwell time scan_home_time Get/Set scan home channel dwell time scan_passive_time Get/Set passive scan channel dwell time scan_nprobes Get/Set scan parameter for number of probes to use per channel scanned prb_resp_timeout Get/Set probe response timeout channel_qa Get last channel quality measurment channel_qa_start Start a channel quality measurment country Select Country Code for driver operational region For simple country setting: wl country Where is either a long name or country code from ISO 3166; for example "Germany" or "DE" For a specific built-in country definition: wl country [] Where is a country country code followed by '/' and regulatory revision number. For example, "US/3". And where is either a long name or country code from ISO 3166. If is omitted, it will be the same as the built-in country code. Use 'wl country list [band(a or b)]' for the list of supported countries country_ie_override To set/get country ie autocountry_default Select Country Code for use with Auto Contry Discovery join Join a specified network SSID. Usage: join [key <0-3>:xxxxx] [imode bss|ibss] [amode open|shared|openshared|wpa|wpapsk|wpa2|wpa2psk|wpanone|ftpsk] [options] Options: -b MAC, --bssid=MAC BSSID (xx:xx:xx:xx:xx:xx) to scan and join -c CL, --chanspecs=CL chanspecs (comma or space separated list) prescanned uses channel and bssid list from scanresults -p, -passive: force passive assoc scan (useful for P2P) ssid Set or get a configuration's SSID. wl ssid [-C num]|[--cfg=num] [] If the configuration index 'num' is not given, configuraion #0 is assumed and setting will initiate an assoication attempt if in infrastructure mode, or join/creation of an IBSS if in IBSS mode, or creation of a BSS if in AP mode. mac Set or get the list of source MAC address matches. wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...] To Clear the list: wl mac none macmode Set the mode of the MAC list. 0 - Disable MAC address matching. 1 - Deny association to stations on the MAC list. 2 - Allow association to stations on the MAC list. wds Set or get the list of WDS member MAC addresses. Set using a space separated list of MAC addresses. wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...] lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone). noise Get noise (moving average) right after tx in dBm fqacurcy Manufacturing test: set frequency accuracy mode. freqacuracy syntax is: fqacurcy Arg is channel number 1-14, or 0 to stop the test. crsuprs Manufacturing test: set carrier suppression mode. carriersuprs syntax is: crsuprs Arg is channel number 1-14, or 0 to stop the test. longtrain Manufacturing test: set longtraining mode. longtrain syntax is: longtrain Arg is A band channel number or 0 to stop the test. band Returns or sets the current band auto - auto switch between available bands (default) a - force use of 802.11a band b - force use of 802.11b band bands Return the list of available 802.11 bands phylist Return the list of available phytypes shortslot Get current 11g Short Slot Timing mode. (0=long, 1=short) shortslot_override Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short) shortslot_restrict Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs. 0 - Do not restrict association based on ShortSlot capability 1 - Restrict association to STAs with ShortSlot capability ignore_bcns AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons) pktcnt Get the summary of good and bad packets. upgrade Upgrade the firmware on an embedded device gmode Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS) gmode_protection Get G protection mode. (0=disabled, 1=enabled) gmode_protection_control Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS) gmode_protection_override Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable) protection_control Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS) legacy_erp Get/Set 11g legacy ERP inclusion (0=disable, 1=enable) scb_timeout AP only: inactivity timeout value for authenticated stas assoclist AP only: Get the list of associated MAC addresses. isup Get driver operational state (0=down, 1=up) rssi Get the current RSSI val, for an AP you must specify the mac addr of the STA rssi_event Set parameters associated with RSSI event notification usage: wl rssi_event rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit. rssi_levels: Variable number of RSSI levels (maximum 8) in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets crosses a level. fasttimer Deprecated. Use fast_timer. slowtimer Deprecated. Use slow_timer. glacialtimer Deprecated. Use glacial_timer. radar Enable/Disable radar radarargs Get/Set Radar parameters in order as version, npulses, ncontig, min_pw, max_pw, thresh0, thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp, min_fm_lp, max_span_lp, min_deltat, max_deltat, autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra, npulses_stg2, npulses_stg3, percal_mask, quant, min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask radarargs40 Get/Set Radar parameters for 40Mhz channel in order as version, npulses, ncontig, min_pw, max_pw, thresh0, thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp, min_fm_lp, max_span_lp, min_deltat, max_deltat, autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra, npulses_stg2, npulses_stg3, percal_mask, quant, min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask radarthrs Set Radar threshold for both 20 & 40MHz & 80MHz BW: order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo thresh0_80_lo, thresh1_80_lo, thresh0_20_hi, thresh1_20_hi thresh0_40_hi, thresh1_40_hi, thresh0_80_hi, thresh1_80_hi dfs_status Get dfs status interference Get/Set interference mitigation mode. Choices are: 0 = none 1 = non wlan 2 = wlan manual 3 = wlan automatic 4 = wlan automatic with noise reduction interference_override Get/Set interference mitigation override. Choices are: 0 = no interference mitigation 1 = non wlan 2 = wlan manual 3 = wlan automatic 4 = wlan automatic with noise reduction -1 = remove override, override disabled frameburst Disable/Enable frameburst mode pwr_percent Get/Set power output percentage toe Enable/Disable tcpip offload feature toe_ol Get/Set tcpip offload components toe_stats Display checksum offload statistics toe_stats_clear Clear checksum offload statistics arpoe Enable/Disable arp agent offload feature arp_ol Get/Set arp offload components arp_peerage Get/Set age of the arp entry in minutes arp_table_clear Clear arp cache ol_notify_bcn_ie Enable/Disable IE ID notification ol_arp_hostip Add a host-ip address or display them ol_nd_hostip Add a local host-ipv6 address or display them arp_hostip Add a host-ip address or display them arp_hostip_clear Clear all host-ip addresses ns_hostip Add a ns-ip address or display then ns_hostip_clear Clear all ns-ip addresses arp_stats Display ARP offload statistics arp_stats_clear Clear ARP offload statistics wet Get/Set wireless ethernet bridging mode bi Get/Set the beacon period (bi=beacon interval) dtim Get/Set DTIM wds_remote_mac Get WDS link remote endpoint's MAC address wds_wpa_role_old Get WDS link local endpoint's WPA role (old) wds_wpa_role Get/Set WDS link local endpoint's WPA role authe_sta_list Get authenticated sta mac address list autho_sta_list Get authorized sta mac address list measure_req Send an 802.11h measurement request. Usage: wl measure_req Measurement types are: TPC, Basic, CCA, RPI Target MAC addr format is xx:xx:xx:xx:xx:xx quiet Send an 802.11h quiet command. Usage: wl quiet , , csa Send an 802.11h channel switch anouncement with chanspec: [a,b][n][u,l][frame type] mode (0 or 1) count (0-254) channel format: 20MHz : [2g|5g][/20] 40MHz : [2g|5g]/40[u,l] 80MHz : [5g]/80 optional band 2g or 5g, default to 2g if channel <= 14 channel number (0-200) bandwidth, 20, 40, or 80, default 20 primary sideband for 40MHz on 2g, l=lower, u=upper csa frame type(optional), default is broadcast if not specified, u=unicast constraint Send an 802.11h Power Constraint IE Usage: wl constraint 1-255 db rm_req Request a radio measurement of type basic, cca, or rpi specify a series of measurement types each followed by options. example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11 Options: -t n numeric token id for measurement set or measurement -c n channel -d n duration in TUs (1024 us) -p parallel flag, measurement starts at the same time as previous Each measurement specified uses the same channel and duration as the previous unless a new channel or duration is specified. rm_rep Get current radio measurement report join_pref Set/Get join target preferences. assoc_pref Set/Get association preference. Usage: wl assoc_pref [auto|a|b|g] wme Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto) wme_ac wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm ] ...] wme_apsd Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on) wme_apsd_sta Set APSD parameters on STA. Driver must be down. Usage: wl wme_apsd_sta : number of frames per USP: 0 (all), 2, 4, or 6 : value 0 to disable, 1 to enable U-APSD per AC wme_dp Set AC queue discard policy. Usage: wl wme_dp : value 0 for newest-first, 1 for oldest-first wme_counters print WMM stats wme_clear_counters clear WMM counters wme_tx_params wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate ] ...] wme_maxbw_params wl wme_maxbw_params [be|bk|vi|vo ....] lifetime Set Lifetime parameter (milliseconds) for each ac. wl lifetime be|bk|vi|vo [] reinit Reinitialize device sta_info wl sta_info staprio Set/Get sta priority Usage: wl staprio : 0~3 pktq_stats Dumps packet queue log info for [C] common, [A] AMPDU, [N] NAR or [P] power save queues A:, N: or P: are used to prefix a MAC address (a colon : separator is necessary), or else C: is used alone. The '+' option after the colon gives more details. Up to 4 parameters may be given, the common queue is default when no parameters are supplied Use '/' as suffix to restrict to certain prec indices; multiple ///...can be used Also, '//' as a suffix to the MAC address or 'C://' will enable automatic logging of all prec as they are seen. Full automatic operation is also possible with the shorthand 'A:' (or 'A://'), 'P:' (or 'P://') etc which scans through all known addresses for those parameters that take a MAC address. wl pktq_stats [C:[+]]|[A:[+]|P:[+]|N:[+]][/[/]][//]... bs_data Display per station band steering data usage: bs_data [options] options are: -comma Use commas to separate values rather than blanks. -tab Use to separate values rather than blanks. -raw Display raw values as received from driver. -noidle Do not display idle stations -noreset Do not reset counters after reading cap driver capabilities malloc_dump Deprecated. Folded under 'wl dump malloc chan_info channel info add_ie Add a vendor proprietary IE to 802.11 management packets Usage: wl add_ie length OUI hexdata : Bit 0 - Beacons Bit 1 - Probe Rsp Bit 2 - Assoc/Reassoc Rsp Bit 3 - Auth Rsp Bit 4 - Probe Req Bit 5 - Assoc/Reassoc Req Example: wl add_ie 3 10 00:90:4C 0101050c121a03 to add this IE to beacons and probe responses del_ie Delete a vendor proprietary IE from 802.11 management packets Usage: wl del_ie length OUI hexdata : Bit 0 - Beacons Bit 1 - Probe Rsp Bit 2 - Assoc/Reassoc Rsp Bit 3 - Auth Rsp Bit 4 - Probe Req Bit 5 - Assoc/Reassoc Req Example: wl del_ie 3 10 00:90:4C 0101050c121a03 list_ie Dump the list of vendor proprietary IEs rand Get a 2-byte Random Number from the MAC's PRNG Usage: wl rand otpraw Read/Write raw data to on-chip otp Usage: wl otpraw [] otpw Write an srom image to on-chip otp Usage: wl otpw file nvotpw Write nvram to on-chip otp Usage: wl nvotpw file bcmerrorstr errorstring freqtrack Set Frequency Tracking Mode (0=Auto, 1=On, 2=OFF) eventing set/get hex filter bitmask for MAC event reporting up to application layer event_msgs set/get hex filter bitmask for MAC event reporting via packet indications counters Return driver counter values delta_stats_interval set/get the delta statistics interval in seconds (0 to disable) delta_stats get the delta statistics for the last interval assoc_info Returns the assoc req and resp information [STA only] beacon_info Returns the 802.11 management frame beacon information Usage: wl beacon_info [-f file] [-r] -f Write beacon data to file -r Raw hex dump of beacon data probe_resp_info Returns the 802.11 management frame probe response information Usage: wl probe_resp_info [-f file] [-r] -f Write probe response data to file -r Raw hex dump of probe response data autochannel auto channel selection: 1 to issue a channel scanning; 2 to set chanspec based on the channel scan result; without argument to only show the chanspec selected; ssid must set to null before this process, RF must be up csscantimer auto channel scan timer in minutes (0 to disable) closed hides the network from active scans, 0 or 1. 0 is open, 1 is hide pmkid_info Returns the pmkid table bss set/get BSS enabled status: up/down closednet set/get BSS closed network attribute ap_isolate set/get AP isolation eap_restrict set/get EAP restriction diag diag testindex(1-interrupt, 2-loopback, 3-memory, 4-led); precede by 'wl down' and follow by 'wl up' reset_d11cnts reset 802.11 MIB counters staname get/set station name: Maximum name length is 15 bytes apname get AP name otpdump Dump raw otp otpstat Dump OTP status nrate "auto" to clear a rate override, or: -r legacy rate (CCK, OFDM) -m HT MCS index -s stf mode (0=SISO,1=CDD,2=STBC,3=SDM) -w Override MCS only to support STA's with/without STBC capability mimo_txbw get/set mimo txbw (2=20Mhz(lower), 3=20Mhz upper, 4=40Mhz) cac_addts add TSPEC, error if STA is not associated or WME is not enabled arg: TSPEC parameter input list cac_delts delete TSPEC, error if STA is not associated or WME is not enabled arg: TSINFO for the target tspec cac_delts_ea delete TSPEC, error if STA is not associated or WME is not enabled arg1: Desired TSINFO for the target tspec arg2: Desired MAC address cac_tslist Get the list of TSINFO in driver eg. 'wl cac_tslist' get a list of TSINFO cac_tslist_ea Get the list of TSINFO for given STA in driver eg. 'wl cac_tslist_ea ea' get a list of TSINFO cac_tspec Get specific TSPEC with matching TSINFO eg. 'wl cac_tspec 0xaa 0xbb 0xcc' where 0xaa 0xbb & 0xcc are TSINFO octets cac_tspec_ea Get specific TSPEC for given STA with matching TSINFO eg. 'wl cac_tspec 0xaa 0xbb 0xcc xx:xx:xx:xx:xx:xx' where 0xaa 0xbb & 0xcc are TSINFO octets and xx is mac address sd_cis dump sdio CIS sd_devreg g/set device register across SDIO bus sd_drivestrength g/set SDIO bus drive strenth in mA sd_hostreg g/set local controller register sd_blockmode g/set blockmode sd_blocksize g/set block size for a function sd_ints g/set client ints sd_dma g/set dma usage sd_numints number of device interrupts sd_numlocalints number of non-device controller interrupts sd_divisor set the divisor for SDIO clock generation sd_mode g/set SDIO bus mode (spi, sd1, sd4) sd_highspeed set the high-speed clocking mode sd_msglevel g/set debug message level overlay overlay virt_addr phy_addr size phy_txpwrindex usage: (set) phy_txpwrindex core0_idx core1_idx core2_idx core3_idx (get) phy_txpwrindex, return format: core0_idx core1_idx core2_idx core3_idxSet/Get txpwrindex rssi_cal_freq_grp_2g usage: wl_rssi_cal_freq_grp_2g [chan_1_2,chan_3_4,...,chan_13_14] Each of the variables like - chan_1_2 is a byteUpper nibble of this byte is for chan1 and lower for chan2MSB of the nibble tells if the channel is used for calibration3 LSB's tell which group the channel falls inSet/get rssi calibration frequency grouping phy_rssi_gain_delta_2gb0 usage: phy_rssi_gain_delta_2gb0 [val0 val1 ....] Number of arguments can be - 8 for single core (4345 and 4350) 9 by specifying core_num followed by 8 arguments (4345 and 4350) 16 for both cores (4350)Set/get rssi gain delta values phy_rssi_gain_delta_2gb1 usage: phy_rssi_gain_delta_2gb1 [val0 val1 ....] Number of arguments can be - 8 for single core (4345 and 4350) 9 by specifying core_num followed by 8 arguments (4345 and 4350) 16 for both cores (4350)Set/get rssi gain delta values phy_rssi_gain_delta_2gb2 usage: phy_rssi_gain_delta_2gb2 [val0 val1 ....] Number of arguments can be - 8 for single core (4345 and 4350) 9 by specifying core_num followed by 8 arguments (4345 and 4350) 16 for both cores (4350)Set/get rssi gain delta values phy_rssi_gain_delta_2gb3 usage: phy_rssi_gain_delta_2gb3 [val0 val1 ....] Number of arguments can be - 8 for single core (4345 and 4350) 9 by specifying core_num followed by 8 arguments (4345 and 4350) 16 for both cores (4350)Set/get rssi gain delta values phy_rssi_gain_delta_2gb4 usage: phy_rssi_gain_delta_2gb4 [val0 val1 ....] Number of arguments can be - 8 for single core (4345 and 4350) 9 by specifying core_num followed by 8 arguments (4345 and 4350) 16 for both cores (4350)Set/get rssi gain delta values phy_rssi_gain_delta_2g usage: phy_rssi_gain_delta_2g [val0 val1 ....] Set/get rssi gain delta values phy_rssi_gain_delta_5gl usage: phy_rssi_gain_delta_5gl [val0 val1 ....] Set/get rssi gain delta values phy_rssi_gain_delta_5gml usage: phy_rssi_gain_delta_5gml [val0 val1 ....] Set/get rssi gain delta values phy_rssi_gain_delta_5gmu usage: phy_rssi_gain_delta_5gmu [val0 val1 ....] Set/get rssi gain delta values phy_rssi_gain_delta_5gh usage: phy_rssi_gain_delta_5gh [val0 val1 ....] Set/get rssi gain delta values phy_rxgainerr_2g usage: phy_rxgainerr_2g [val0 val1 ....] Set/get rx gain delta values phy_rxgainerr_5gl usage: phy_rxgainerr_5gl [val0 val1 ....] Set/get rx gain delta values phy_rxgainerr_5gm usage: phy_rxgainerr_5gml [val0 val1 ....] Set/get rx gain delta values phy_rxgainerr_5gh usage: phy_rxgainerr_5gmu [val0 val1 ....] Set/get rx gain delta values phy_rxgainerr_5gu usage: phy_rxgainerr_5gh [val0 val1 ....] Set/get rx gain delta values phy_test_tssi wl phy_test_tssi val phy_test_tssi_offs wl phy_test_tssi_offs val phy_rssiant wl phy_rssiant antindex(0-3) phy_rssi_ant Get RSSI per antenna (only gives RSSI of current antenna for SISO PHY) lpphy_papdepstbl print papd eps table; Usage: wl lpphy_papdepstbl phy_test_idletssi get idletssi for the given core; wl phy_test_idletssi corenum phy_setrptbl populate the reciprocity compensation table based on SROM cal content usage: wl phy_setrptbl phy_forceimpbf force the beamformer into implicit TXBF mode and ready to construct steering matrix usage: wl phy_forceimpbf phy_forcesteer force the beamformer to apply steering matrix when TXBF is turned on usage: wl phy_forcesteer 1/0 lcnphy_papdepstbl print papd eps table; Usage: wl lcnphy_papdepstbl rifs set/get the rifs status; usage: wl rifs <1/0> (On/Off) rifs_advert set/get the rifs mode advertisement status; usage: wl rifs_advert <-1/0> (Auto/Off) phy_rxiqest Get phy RX IQ noise in dBm: -s # of samples (2^n) -a antenna select, 0,1 or 3 -r resolution select, 0 (coarse) or 1 (fine) -f lpf hpc override select, 0 (hpc unchanged) or 1 (overridden to ltrn mode) -w dig lpf override select, 0 (lpf unchanged) or 1 (overridden to ltrn_lpf mode) or 2 (bypass) -g gain-correction select, 0 (disable), 1(enable full correction) 2 (enable temperature correction) or 3(verify rssi_gain_delta) -e extra INITgain in dB on top of default. Valid values = {0, 3, 6, .., 21, 24} -i gain mode select, 0 (default gain), 1 (fixed high gain) or 4 (fixed low gain). phy_txiqcc usage: phy_txiqcc [a b] Set/get the iqcc a, b values phy_txlocc usage: phy_txlocc [di dq ei eq fi fq] Set/get locc di dq ei eq fi fq values phytable usage: wl phytable table_id offset width_of_table_element [table_element] Set/get table element of a table with the given ID at the given offset Note that table width supplied should be 8 or 16 or 32 table ID, table offset can not be negative ota_teststop Usage: ota_teststop ota_loadtest Usage: ota_loadtest [filename] picks up ota_test.txt if file is not given ota_stream Usage: wl ota_stream start : to start the test wl ota_stream ota_sync wl ota_stream test_setup synchtimeoout(seconds) synchbreak/loop synchmac txmac rxmac wl ota_stream ota_tx chan bandwidth contrlchan rates stf txant rxant tx_ifs tx_lennum_pkt pwrctrl start:delta:end wl ota_stream ota_rx chan bandwidth contrlchan -1 stf txant rxant tx_ifstx_len num_pkt wl ota_stream stop : to stop the test ota_teststatus Usage: otatest_status Displays current running test details otatest_status n displays test arguments for nth line force_vsdb_chans Set/get channels for forced vsdb mode usage: wl force_vsdb_chans chan1 chan2 Note: Give chan in the same format as chanspec: eg force_vsdb_chans 1l 48u pavars Set/get temp PA parameters usage: wl down wl pavars pa2gw0a0=0x1 pa2gw1a0=0x2 pa2gw2a0=0x3 ... wl pavars wl up override the PA parameters after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up PA parameters in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 povars Set/get temp power offset usage: wl down wl povars cck2gpo=0x1 ofdm2gpo=0x2 mcs2gpo=0x3 ... wl povars wl up override the power offset after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up power offsets in one band range (2g, 5gl, 5g, 5gh) must all present if one of them is specified in the command, otherwise it will be filled with 0 cck(2g only), ofdm, and mcs(0-7) for NPHY are supported rpcalvars Set/get temp RPCAL parameters usage: wl down wl rpcalvars rpcal2g=0x1 wl rpcalvars wl up override the RPCAL parameters after driver attach(srom read), before diver up These override values will be propogated to HW when driver goes up Only the RPCAL parameter specified in the command is updated, the rest is untouched fem Set temp fem2g/5g value usage: wl fem (tssipos2g=0x1 extpagain2g=0x2 pdetrange2g=0x1 triso2g=0x1 antswctl2g=0) (tssipos5g=0x1 extpagain5g=0x2 pdetrange5g=0x1 triso5g=0x1 antswctl5g=0) antgain Set temp ag0/1 value usage: wl antgain ag0=0x1 ag1=0x2 maxpower Set temp maxp2g(5g)a0(a1) value usage: wl maxpower maxp2ga0=0x1 maxp2ga1=0x2 maxp5ga0=0xff maxp5ga1=0xff maxp5gla0=0x3 maxp5gla1=0x4 maxp5gha0=0x5 maxp5gha1=0x6 phy_antsel get/set antenna configuration set: -1(AUTO), 0xAB(fixed antenna selection) where A and B is the antenna numbers used for RF chain 1 and 0 respectively query: [AUTO] [AUTO] [AUTO] [AUTO] where utx = TX unicast antenna configuration urx = RX unicast antenna configuration dtx = TX default (non-unicast) antenna configuration drx = RX default (non-unicast) antenna configuration txcore Usage: wl txcore -k -o -s <1..4> -c -k CCK core mask -o OFDM core mask -s # of space-time-streams -c active core (bitmask) to be used when transmitting frames txcore_override Usage: wl txcore_override get the user override of txcore txchain_pwr_offset Usage: wl txchain_pwr_offset [qdBm offsets] Get/Set the current offsets for each core in qdBm (quarter dBm) sample_collect Optional parameters ACPHY/HTPHY/(NPHY with NREV >= 7) are: -f File name to dump the sample buffer (default "sample_collect.dat") -t Trigger condition (default now) now, good_fcs, bad_fcs, bad_plcp, crs, crs_glitch, crs_deassert -b PreTrigger duration in us (default 10) -a PostTrigger duration in us (default 10) -m Sample collect mode (default 1) SC_MODE_0_sd_adc 0 SC_MODE_1_sd_adc_5bits 1 SC_MODE_2_cic0 2 SC_MODE_3_cic1 3 SC_MODE_4s_rx_farrow_1core 4 SC_MODE_4m_rx_farrow 5 SC_MODE_5_iq_comp 6 SC_MODE_6_dc_filt 7 SC_MODE_7_rx_filt 8 SC_MODE_8_rssi 9 SC_MODE_9_rssi_all 10 SC_MODE_10_tx_farrow 11 SC_MODE_11_gpio 12 SC_MODE_12_gpio_trans 13 SC_MODE_14_spect_ana 14 SC_MODE_5s_iq_comp 15 SC_MODE_6s_dc_filt 16 SC_MODE_7s_rx_filt 17 HTPHY: 0=adc, 1..3=adc+rssi, 4=gpio NPHY: 1=Dual-Core adc[9:2], 2=Core0 adc[9:0], 3=Core1 adc[9:0], gpio=gpio -g GPIO mux select (default 0) use only for gpio mode -d Downsample enable (default 0) use only for HTPHY -e BeDeaf enable (default 0) -i Timeout in units of 10us. (ACPHY is in 10ms unit) (default 1000) Optional parameters (NPHY with NREV < 7) are: -f File name to dump the sample buffer (binary format, default "sample_collect.dat") -u Sample collect duration in us (default 60) -c Cores to do sample collect, only if BW=40MHz (default both) Optional parameters LCN40PHY are: -f File name to dump the sample buffer (default "sample_collect.dat") -t Trigger condition (default now) now -s Trigger State (default 0) -x Module_Sel1 (default 2) -y Module_Sel2 (default 6) -n Number of samples (Max 2048, default 2048) For (NREV < 7), the NPHY buffer returned has the format: In 20MHz [(uint16)num_bytes, ] In 40MHz [(uint16)num_bytes(core0), , (uint16)num_bytes(core1), ] txfifo_sz set/get the txfifo size; usage: wl txfifo_sz pfnset Configures preferred network offload parameter pfnset syntax is: pfnset [scanfrq xxxxx(30 sec)] [netimeout xxxx(60 sec)][slowfrq xxxx(180 sec)] [bestn (2)|[1-BESTN_MAX]] [mscan (0)|[0-MSCAN_MAX]][bdscan (0)|1] [adapt (off)|[smart, strict, slow]][rssi_delta xxxx(30 dBm)] [sort (listorder)|rssi] [bkgscan (0)|1] [immediateevent (0)|1][immediate 0|(1)] [repeat (10)|[1-20]] [exp (2)|[1-5]] [separate 0|(1)] pfnadd Adding SSID based preferred networks to monitor and connect pfnadd syntax is: pfnadd ssid [hidden (0)|1][imode (bss)|ibss][amode (open)|shared] [wpa_auth (wpadisabled)|wpapsk|wpa2psk|wpanone|any][wsec WEP|TKIP|AES|TKIPAES] [suppress (neither)|found|lost] [rssi (0 dBm)] Up to 16 SSID networks can be added together in one pfnadd To specify more than one WPA methods, use a number (same format as wpa_auth iovar) as the parameter of wpa_auth (e.g. 0x84 for wpapsk and wpa2psk.) pfnadd_bssid Adding BSSID based preferred networks to monitor and connect pfnadd_bssid syntax is: pfnadd_bssid bssid [suppress (neither)|found|lost][rssi (0 dBm)] Up to 150 BSSIDs can be added together in one pfnadd_bssid pfncfg Configures channel list and report type Usage: pfncfg [channel ] [report ] [prohibited 1|0] report is ssidonly, bssidonly, or both (default: both) prohibited flag 1: allow and (passively) scan any channel (default 0) pfn Enable/disable preferred network off load monitoring pfn syntax is: pfn 0|1 pfnclear Clear the preferred network list pfnclear syntax is: pfnclear pfnbest Get the best n networks in each of up to m scans, with 16bit timestamp pfnbest syntax is: pfnbest pfnlbest Get the best n networks in each scan, up to m scans, with 32bit timestmp pfnbest syntax is: pfnlbest pfnsuspend Suspend/resume pno scan pfnsuspend syntax is: pfnsuspend 0|1 pfnmem Get supported mscan with given bestn pfnmem syntax is: pfnmscan bestn [1-BESTN_MAX] pfneventchk Listen and prints the preferred network off load event from dongle pfneventchk syntax is: pfneventchk [ifname] escan_event_check Listen and prints the escan events from the dongle escan_event_check syntax is: escan_event_check ifname flag flag 1 = sync_id info, 2 = bss info, 4 = state + bss info [default], 8 = TLV check for IEs escanresults Start escan and display results. Default to an active scan across all channels for any SSID. Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated). Options: -s S, --ssid=S SSIDs to scan -t ST, --scan_type=ST [active|passive|prohibit|offchan|hotspot] scan type --bss_type=BT [bss/infra|ibss/adhoc] bss type to scan -b MAC, --bssid=MAC particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx -n N, --nprobes=N number of probes per scanned channel -a N, --active=N dwell time per channel for active scanning -p N, --passive=N dwell time per channel for passive scanning -h N, --home=N dwell time for the home channel between channel scans -c L, --channels=L comma or space separated list of channels to scan event_filter Set/get event filter event_filter syntax is: event_filter [value] p2po_listen start listen (with period and interval) usage: p2po_listen ["period"] ["interval"] p2po_find start discovery p2po_stop stop both P2P listen and P2P device discovery offload(0:stop; 1:pause). usage: p2po_stop <0|1> p2po_addsvc add query-service pair usage: p2po_addsvc <"query"> <"response"> : 1 = Bonjour, 2 = UPnP p2po_delsvc delete query-service pair usage: p2po_delsvc <"query"> : 1 = Bonjour, 2 = UPnP, 0 = delete all p2po_sd_req_resp find a service usage: p2po_sd_req_resp <"query"> : 1 = Bonjour, 2 = UPnP p2po_sd_cancel cancel finding a service p2po_listen_channel set listen channel to channel 1, 6, 11, or default usage: p2po_listen_channel <1|6|11|0> p2po_results Listens and displays P2PO results. anqpo_set set ANQP offload parameters usage: anqpo_set [max_retransmit ] [response_timeout ] [max_comeback_delay ] [max_retries ] [query "encoded ANQP query"] anqpo_stop_query stop ANQP query usage: anqpo_stop_query anqpo_start_query start ANQP query to peer(s) usage: anqpo_start_query [ ]> anqpo_auto_hotspot automatic ANQP query to maximum number of hotspot APs, default 0 (disabled) usage: anqpo_auto_hotspot [max] anqpo_ignore_mode ignore duplicate SSIDs or BSSIDs, default 0 (SSID) usage: anqpo_ignore_mode [0 (SSID) | 1 (BSSID)] anqpo_ignore_ssid_list get, clear, set, or append to ANQP offload ignore SSID list usage: wl anqpo_ignore_ssid_list [clear | set [ssid2] | append [ssid4]> anqpo_ignore_bssid_list get, clear, set, or append to ANQP offload ignore BSSID list usage: wl anqpo_ignore_bssid_list [clear | set [xx:xx:xx:xx:xx:xx] | append [xx:xx:xx:xx:xx:xx]]> anqpo_results Listens and displays ANQP results. hs20_ie set hotspot 2.0 indication IE usage: wl hs20_ie rate_histo Get rate hostrogram pkteng_start start packet engine tx usage: wl pkteng_start [(async)|sync] [ipg] [len] [nframes] [src] start packet engine rx usage: wl pkteng_start [(async)|sync] [rxframes] [rxtimeout] sync: synchronous mode ipg: inter packet gap in us len: packet length nframes: number of frames; 0 indicates continuous tx test src: source mac address rxframes: number of receive frames (sync mode only) rxtimeout: maximum timout in msec (sync mode only) pkteng_stop stop packet engine; usage: wl pkteng_stop pkteng_stats packet engine stats; usage: wl pkteng_stats wowl Enable/disable WOWL events 0 - Clear all events Bit 0 - Wakeup on Magic Packet Bit 1 - Wakeup on NetPattern (use 'wl wowl_pattern' to configure pattern) Bit 2 - Wakeup on loss-of-link due to Disassociation/Deauth Bit 3 - Wakeup on retrograde tsf Bit 4 - Wakeup on loss of beacon (use 'wl wowl_bcn_loss' to configure time) wowl_bcn_loss Set #of seconds of beacon loss for wakeup event wowl_pattern usage: wowl_pattern [ [clr | [[ add | del ] offset mask value ]]] No options -- lists existing pattern list add -- Adds the pattern to the list del -- Removes a pattern from the list clr -- Clear current list offset -- Starting offset for the pattern mask -- Mask to be used for pattern. Bit i of mask => byte i of the pattern value -- Value of the pattern wowl_keepalive Send specified keep alive packet periodically in wowl mode. Usage: wl wowl_keepalive index: 0 - 1. period: Re-transmission period in milli-seconds. 0 to disable packet transmits. packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order. e.g. Send keep alive packet every 30 seconds using id-1: wl wowl_keepalive 1 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d wowl_wakeind usage: wowl_wakeind [clear] Shows last system wakeup event indications from PCI and D11 cores clear - Clear the indications wowl_status usage: wowl_status [clear] Shows last system wakeup setting wowl_pkt Send a wakeup frame to wakup a sleeping STA in WAKE mode Usage: wl wowl_pkt >[ magic [] | net ] e.g. To send bcast magic frame -- wl wowl_pkt 102 bcast magic 00:90:4c:AA:BB:CC To send ucast magic frame -- wl wowl_pkt 102 ucast 00:90:4c:aa:bb:cc magic To send a frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc net 0 0x00904caabbcc 0x03 NOTE: offset for netpattern frame starts from "Dest EA" of ethernet frame.So dest ea will be used only when offset is >= 6 To send a eapol identity frame with L2 unicast - wl wowl_pkt 102 00:90:4c:aa:bb:cc eapid id-string wowl_ext_magic Set 6-byte extended magic pattern Usage: wl wowl_ext_magic 0x112233445566 wme_apsd_trigger Set Periodic APSD Trigger Frame Timer timeout in ms (0=off) wme_autotrigger Enable/Disable sending of APSD Trigger frame when all ac are delivery enabled reassoc Initiate a (re)association request. Usage: wl reassoc [options] Options: -c CL, --chanspecs=CL chanspecs (comma or space separated list) send_nulldata Sed a null frame to the specified hw address btc_params g/set BT Coex parameters btc_flags g/set BT Coex flags obss_scan_params set/get Overlapping BSS scan parameters Usage: wl obss_scan a b c d e ...; where a-Passive Dwell, {5-1000TU}, default = 100 b-Active Dwell, {10-1000TU}, default = 20 c-Width Trigger Scan Interval, {10-900sec}, default = 300 d-Passive Total per Channel, {200-10000TU}, default = 200 e-Active Total per Channel, {20-1000TU}, default = 20 f-Channel Transition Delay Factor, {5-100}, default = 5 g-Activity Threshold, {0-100%}, default = 25 mkeep_alive Send specified "mkeep-alive" packet periodically. Usage: wl mkeep_alive index: 0 - 3. period: Re-transmission period in milli-seconds. 0 to disable packet transmits. packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order. If no packet is specified, a nulldata frame will be sent instead. e.g. Send keep alive packet every 30 seconds using id-1: wl mkeep_alive 1 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d keep_alive Send specified "keep-alive" packet periodically. Usage: wl keep_alive period: Re-transmission period in milli-seconds. 0 to disable packet transmits. packet: Hex packet contents to transmit. The packet contents should include the entire ethernet packet (ethernet header, IP header, UDP header, and UDP payload) specified in network byte order. e.g. Send keep alive packet every 30 seconds: wl keep_alive 30000 0x0014a54b164f000f66f45b7e08004500001e000040004011c52a0a8830700a88302513c413c4000a00000a0d srchmem g/set ucode srch engine memory pkt_filter_add Install a packet filter. Usage: wl pkt_filter_add id: Integer. User specified id. type: 0 (Pattern matching filter). offset: Integer. Offset within received packets to start matching. polarity: Set to 1 to negate match result. 0 is default. bitmask: Hex bitmask that indicates which bits of 'pattern' to match. Must be same size as 'pattern'. Bit 0 of bitmask corresponds to bit 0 of pattern, etc. If bit N of bitmask is 0, then do *not* match bit N of the pattern with the received payload. If bit N of bitmask is 1, then perform match. pattern: Hex pattern to match. pkt_filter_clear_stats Clear packet filter statistic counter values. Usage: wl pkt_filter_clear_stats pkt_filter_enable Enable/disable a packet filter. Usage: wl pkt_filter_enable <0|1> pkt_filter_list List installed packet filters. Usage: wl pkt_filter_list [val] val: 0 (disabled filters) 1 (enabled filters) pkt_filter_mode Set packet filter match action. Usage: wl pkt_filter_mode value: 1 - Forward packet on match, discard on non-match (default). 0 - Discard packet on match, forward on non-match. pkt_filter_delete Uninstall a packet filter. Usage: wl pkt_filter_delete pkt_filter_stats Retrieve packet filter statistic counter values. Usage: wl pkt_filter_stats trf_mgmt_config Sets/gets traffic management configuration. Usage: wl trf_mgmt_config [ [ []]] enable: 0 - Disable traffic management 1 - Enables traffic management (host IP arguments required) Flag values are the following: 0x0001 : Add DSCP values to tx packets 0x0002 : Disable traffic shaping...just do priority classification If no arguments are entered, the current traffic management configuration is displayed. e.g. Configure traffic management and specify local ip addr. and bandwidth data: wl trf_mgmt_config 1 12.0.0.1 255.0.0.0 5000 650 trf_mgmt_filters_add Adds a traffic management filter. Usage: wl trf_mgmt_filter_add [dst_port src_port prot priority] dst_port : Destination TCP or UDP port src_port : Source TCP or UDP port (0 - wildcard for any source port) prot : L4 protocol (6 - TCP, 17 - UDP) priority : Priority value (see trf_mgmt_priority_values enum) e.g. Add a tcp wildcard filter: wl trf_mgmt_filters_add 80 0 6 2 trf_mgmt_filters_addex Adds a traffic management filter. Usage: wl trf_mgmt_filter_add flag [dst_port src_port prot priority] Usage: wl trf_mgmt_filter_add flag [dst_mac priority] Flag values are the following: 0x0000 : filter on tcp/udp src/dst port 0x0001 : filter on destination MAC address 0x0010 : do not update the packet priority 0x0020 : Tag packets as Favored dst_mac : Destination MAC address dst_port : Destination TCP or UDP port src_port : Source TCP or UDP port (0 - wildcard for any source port) prot : L4 protocol (6 - TCP, 17 - UDP) priority : Priority value (see trf_mgmt_priority_values enum) e.g. Add a tcp wildcard filter for all src/dst ports: wl trf_mgmt_filters_addex 0 0 0 6 2 e.g. Add a dst mac address filter wl trf_mgmt_filters_addex 0x31 aa:bb:cc:dd:ee:ff 2 trf_mgmt_filters_remove Removes a traffic management filter. Usage: wl trf_mgmt_filter_remove [dst_port src_port prot] dst_port : Destination TCP or UDP port src_port : Source TCP or UDP port (0 - wildcard for any source port) prot : L4 protocol (6 - TCP, 17 - UDP) e.g. Remove a tcp wildcard filter: wl trf_mgmt_filters_remove 80 0 6 trf_mgmt_filters_removeex Removes a traffic management filter. Usage: wl trf_mgmt_filter_remove flag [dst_port src_port prot] Usage: wl trf_mgmt_filter_remove flag [dst_mac] Flag values are the following: 0x0000 : filter on tcp/udp src/dst port 0x0001 : filter on destination MAC address 0x0010 : do not update the packet priority 0x0020 : Tag packets as Favored dst_mac : Destination MAC address dst_port : Destination TCP or UDP port src_port : Source TCP or UDP port (0 - wildcard for any source port) prot : L4 protocol (6 - TCP, 17 - UDP) e.g. Remove a tcp wildcard filter: wl trf_mgmt_filters_removeex 0 80 0 6 wl trf_mgmt_filters_removeex 0x31 00:90:4c:52:a8:83 trf_mgmt_filters_list Lists all traffic management filters. Usage: wl trf_mgmt_filter_list trf_mgmt_filters_clear Clears all traffic management filters. Usage: wl trf_mgmt_filters_clear trf_mgmt_bandwidth Sets/gets traffic management bandwidth configuration. Usage: wl trf_mgmt_bandwidth [downlink uplink min_tx_bk min_tx_be min_tx_vi [min_rx_b min_rx_be min_rx_vi]] downlink : downlink bandwidth (kbps) uplink : uplink bandwidth (kbps) min_tx_bk : min. guaranteed tx bandwidth percentage for BK (kbps) min_tx_be : min. guaranteed tx bandwidth percentage for BE (kbps) min_tx_vi : min. guaranteed tx bandwidth percentage for VI (kbps) (min_tx_bo + min_tx_be + min_tx_vi) must equal 100. min_rx_bk : min. guaranteed rx bandwidth percentage for BK (kbps) min_rx_be : min. guaranteed rx bandwidth percentage for BE (kbps) min_rx_vi : min. guaranteed rx bandwidth percentage for VI (kbps) (min_rx_bk + min_rx_be + min_rx_vi) must equal 100. If no rx gandwidth arguments are entered, tx bandwidth is used for rx. If no arguments are entered, the current bandwidth configuration is displayed. trf_mgmt_flags Sets/gets traffic management operational flags. Usage: wl trf_mgmt_flags [flags] Flag values are the following: 0x0001 : Add DSCP values to tx packets 0x0002 : Disable traffic shaping...just do priority classification If no arguments are entered, the current operational flags are displayed. trf_mgmt_stats Gets traffic management statistics. Usage: wl trf_mgmt_stats [index] index : Queue index trf_mgmt_stats_clear Clears traffic management statistics. Usage: wl trf_mgmt_stats_clear trf_mgmt_shaping_info Gets traffic management shaping parameters. Usage: wl trf_mgmt_shaping_info [index] index : Queue index seq_start Initiates command batching sequence. Subsequent IOCTLs will be queued until seq_stop is received. seq_stop Defines the end of command batching sequence. Queued IOCTLs will be executed. seq_delay Driver should spin for the indicated amount of time. It is only valid within the context of batched commands. seq_error_index Used to retrieve the index (starting at 1) of the command that failed within a batch clmload Used to download CLM data onto the dongle bmac_reboot Reboot BMAC findserver Used to find the remote server with proper mac address given by the user,this cmd is specific to wifi protocol. txmcsset get Transmit MCS rateset for 11N device rxmcsset get Receive MCS rateset for 11N device mimo_ss_stf get/set SS STF mode. Usage: wl mimo_ss_stf <-b a | b> value: 0 - SISO; 1 - CDD -b(band): a - 5G; b - 2.4G extlog get external logs Usage: wl extlog from_last: 1 - from the last log record; 0 - whole log recrods number: number of log records to get, MAX is 32. extlog_clr clear external log records extlog_cfg get/set external log configuration assertlog get external assert logs Usage: wl assertlog assert_type set/get the asset_bypass flag; usage: wl assert_type <1/0> (On/Off) ledbh set/get led behavior Usage: wl ledbh [0-3] [0-15] obss_coex_action send OBSS 20/40 Coexistence Mangement Action Frame Usage: wl obss_coex_action -i <1/0> -w <1/0> -c -i: 40MHz intolerate bit; -w: 20MHz width Req bit; -c: channel list, 1 - 14 At least one option must be provided chanim_state get channel interference state Usage: wl chanim_state channel Valid channels: 1 - 14 returns: 0 - Acceptable; 1 - Severe chanim_mode get/set channel interference measure (chanim) mode Usage: wl chanim_mode value: 0 - disabled; 1 - detection only; 2 - detection and avoidance ledbh set/get led behavior Usage: wl ledbh [0-3] [0-15] led_blink_sync set/get led_blink_sync Usage: wl led_blink_sync [0-3] [0/1] cca_get_stats Usage: wl cca_stats [-c channel] [-s num seconds][-n] -c channel: Optional. specify channel. 0 = All channels. Default = current channel -n: no analysis of results -s num_seconds: Optional. Default = 10, Max = 60 -i: list individual measurements in addition to the averages -curband: Only recommend channels on current band itfr_get_stats get interference source information itfr_enab get/set STA interference detection mode(STA only) 0 - disable 1 - enable maual detection 2 - enable auto detection itfr_detect issue an interference detection request smfstats get/clear selected management frame (smf) stats wl smfstats [-C num]|[--cfg=num] [auth]|[assoc]|[reassoc]|[clear] clear - to clear the stats dongleset Enable uart driver manfinfo show chip package info in OTP rrm enable or disable RRM feature Usage: wl rrm [0/1] to disable/enable RRM feature rrm_bcn_req send 11k beacon measurement request Usage: wl rrm_bcn_req [bcn mode] [da] [duration] [random int] [channel] [ssid] [repetitions] rrm_chload_req send 11k channel load measurement request Usage: wl rrm_chload_req [regulatory] [da] [duration] [random int] [channel] [repetitions] rrm_noise_req send 11k noise measurement request Usage: wl rrm_noise_req [regulatory] [da] [duration] [random int] [channel] [repetitions] rrm_frame_req send 11k frame measurement request Usage: wl rrm_frame_req [regulatory] [da] [duration] [random int] [channel] [ta] [repetitions] rrm_stat_req send 11k stat measurement request Usage: wl rrm_stat_req [da] [random int] [duration] [peer] [group id] [repetitions] rrm_lm_req send 11k link measurement request Usage: wl rrm_lm_req [da] rrm_nbr_req send 11k neighbor report measurement request Usage: wl rrm_nbr_req [ssid] rrm_nbr_list get 11k neighbor report list Usage: wl rrm_nbr_list rrm_nbr_del_nbr delete node from 11k neighbor report list Usage: wl rrm_nbr_del_nbr [bssid] rrm_nbr_add_nbr add node to 11k neighbor report list Usage: wl rrm_nbr_add_nbr [bssid] [bssid info] [regulatory] [channel] [phytype] wnm set driver wnm feature mask type 'wl msglevel ?' for values wnm_bsstq send 11v BSS transition management query Usage: wl wnm_bsstq [ssid] tclas_add add tclas frame classifier type entry Usage: wl tclas_add <...> type 0 eth2: type 1/4 ipv4: type 2 802.1Q: type 3 filter: type 4 ipv6: type 5 802.1D/Q: <802.1Q PCP> <802.1Q CFI> <802.1Q VID> tclas_del delete tclas frame classifier type entry Usage: wl tclas_del [ []] tclas_list list the added tclas frame classifier type entry Usage: wl tclas_list wnm_tfsreq_add add one tfs request element and send tfs request frame Usage: wl wnm_tfsreq_add tfs_id: a non-zero value (1 ~ 255) tfs_action_code bitfield: 1: delete after match, 2: notify tfs_subelem_id: TFS subelement (0 for none or 1 for previous tclas_add) send: 0: store element, 1: send all stored elements wnm_dms_set Optionally add pending DMS desc (after tclas_add) and optionally register all desc on AP side to enable the service (with send=1) Usage: wl wnm_dms_set [ []] send: 0: store descriptor, 1: send all stored descs/enable DMS on AP user_id: new ID to assign to the created desc (if TCLAS added) or existing ID to enable on AP (if no TCLAS added), 0 for all desc tc_pro: TCLAS processing element (if several TCLAS added) wnm_dms_status list all DMS descriptors and provide their internal and AP status Usage: wl wl_wnm_dms_status wnm_dms_term Disable registered DMS des on AP side and optionally discard them Usage: wl wnm_dms_term [] del: Discard desc after disabling the service on AP side user_id: desc to disable/delete, 0 for all desc wnm_service_term Disable service. Check specific wnm_XXX_term for more info Usage: wl wnm_service_term srv: 1 for DMS, 2 for FMS, 3 for TFS wnm_timbc_offset get/set TIM broadcast offset by -32768 period > offset(us) > 32768 CAUTION!! Due to resource limitation, one radio can have only one set of TIMBC offset setting. MBSS need to share the same setting Usage: wl wnm_timbc_offset [ [ []]] offset: in unit of us. Transmit TIM frame in specific TBTT transmit time time tsf_present: can be omitted. If set to 1, timestamp field will present in TIM frame.If omitted, default setup to 1 fix_interval: can be omitted. If set with non-zero value, override STA request interval in TIM Broadcast request. If omitted, default setup to 0 rate_override: can be omitted. In unit of 500k, max setup to 108. If set, overrideoverride high rate used to transmit TIM broadcast high rate frame wnm_timbc_set Enable/disable TIM Broadcast. Station will send appropriate request if AP suport TIMBC Usage: wl wnm_timbc_set [ [ []]] interval: Beacon interval requested for TIM frames, 0 to disable TIM BC flags: Bitfield with minimal requirements to keep the service enabled (check doc) min_rate: Minimal rate requirement, in Mbps, for TIM high or low rate frames max_rate: Maximal rate requirement wnm_timbc_status Retrieve TIM Broadcast configuration set with current AP wnm_maxidle setup WNM BSS Max Idle Period interval and option Usage: wl wnm_maxidle