鸿蒙标准系统emmc挂死

简要描述：在Hi3616DV300的板子上，开机uboot出现emmc_init失败的报错，但emmc能正常读写。在启动过程中，多次报himci: card disconnected!及himci: card connected!后系统挂死

**【环境信息】:** 
- 硬件型号：soc：Hi3616DV300   emmc：KLMAG2GEND
- 软件版本信息或tag节点:commit 7cf126aad7a718b26249c4ec4c63f5f14827e9cd
- 测试环境：鸿蒙标准系统
- 其他

**【出现概率】：必现**

**【定位信息】：板子是自研的，可以跑海思的LinuxSDK，硬件排查了没发现什么问题。**

- 1. Log、截图、多媒体文件等，所有和问题有关的信息：

[BEGIN] 2021/6/22 16:08:48

System startup

Uncompress Ok!

U-Boot 2020.01 (Apr 22 2021 - 23:59:39 +0800)hi3516dv300

DRAM:  MMC:   
EMMC/MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:1
mix set temp-phase 3
scan elemnts: startp:4 endp:108
Tuning SampleClock. mix set phase:[04/07] ele:[2d/14]
MMC/SD Card:
    MID:         0x15
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7448M Bytes (High Capacity)
    Name:        "8GTF4"
    Chip Type:   MMC
    Version:     0.0
    Speed:       100000000Hz
    Bus Width:   4bit

EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
mmc_init failed! err:-95
No SD device found !
himci: 0 (eMMC), himci: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
@@@ 5 blocks read: OK
@@@ UpdateMessage.command = ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, UpdateMessage.update = ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
@@@ partitions info from misc =ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, partStrLen = 511
@@@ UpdateMessage.command = ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, g_isRecovery = 0
@@@ g_bootArgsStr = mem=640M console=ttyAMA0,115200 mmz=anonymous,0,0xA8000000,384M clk_ignore_unused androidboot.selinux=permissive skip_initramfs rootdelay=10 init=/init root=/dev/mmcblk0p5 rootfstype=ext4 rw blkdevparts=mmcblk0:1M(boot),15M(kernel),20M(updater),1M(misc),3307M(system),256M(vendor),-(userdata)
@@@ do_bootx in misc_init_r, g_isRecovery = 0
Net:   eth0
Error: eth0 address not set.

Hit any key to stop autoboot:  0

MMC read: dev # 0, block # 2048, count 18432 ... 18432 blocks read: OK
45.24 MB/s
## Booting kernel from Legacy Image at 80000000 ...
   Image Name:   Linux-4.19.155+
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4835814 Bytes = 4.6 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 4.19.155+ (chenxinhan@compile-etherLab) (Android (dev based on r353983c) clang version 9.0.3 (https://android.googlesource.com/toolchain/clang 745b335211bb9eadfa6aa6301f84715cee4b37c5) (https://android.googlesource.com/toolchain/llvm 60cf23e54e46c807513f7a36d0a7b777920b5881) (based on LLVM 9.0.3svn)) #1 SMP Tue Jun 22 15:27:18 CST 2021
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: Hisilicon HI3516DV300 DEMO Board
Memory policy: Data cache writealloc
cma: Reserved 64 MiB at 0xa4000000
random: get_random_bytes called from start_kernel+0x88/0x330 with crng_init=0
percpu: Embedded 14 pages/cpu s27276 r8192 d21876 u57344
Built 1 zonelists, mobility grouping on.  Total pages: 162560
Kernel command line: mem=640M console=ttyAMA0,115200 mmz=anonymous,0,0xA8000000,384M clk_ignore_unused androidboot.selinux=permissive skip_initramfs rootdelay=10 init=/init root=/dev/mmcblk0p5 rootfstype=ext4 rw blkdevparts=mmcblk0:1M(boot),15M(kernel),20M(updater),1M(misc),3307M(system),256M(vendor),-(userdata)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 571744K/655360K available (8192K kernel code, 240K rwdata, 1852K rodata, 1024K init, 339K bss, 18080K reserved, 65536K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xe8800000 - 0xff800000   ( 368 MB)
    lowmem  : 0xc0000000 - 0xe8000000   ( 640 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0x(ptrval) - 0x(ptrval)   (9184 kB)
      .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
      .data : 0x(ptrval) - 0x(ptrval)   ( 241 kB)
       .bss : 0x(ptrval) - 0x(ptrval)   ( 340 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
Gic dist init...
arch_timer: CPU0: Trapping CNTVCT access
arch_timer: cp15 timer(s) running at 50.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns
Switching to timer-based delay loop, resolution 20ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux:  Initializing.
AppArmor: AppArmor disabled by boot time parameter
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80100000 - 0x80100060
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs ...
arch_timer: CPU1: Trapping CNTVCT access
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (200.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(0.010:1): state=initialized audit_enabled=0 res=1
Serial: AMBA PL011 UART driver
120a0000.uart: ttyAMA0 at MMIO 0x120a0000 (irq = 21, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
SCSI subsystem initialized
ssp-pl022 120c0000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 120c0000.spi: mapped registers from 0x120c0000 to (ptrval)
ssp-pl022 120c1000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 120c1000.spi: mapped registers from 0x120c1000 to (ptrval)
ssp-pl022 120c2000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 120c2000.spi: mapped registers from 0x120c2000 to (ptrval)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
videodev: Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
workingset: timestamp_bits=30 max_order=18 bucket_order=0
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
io scheduler mq-deadline registered
io scheduler kyber registered
pl061_gpio 120d0000.gpio_chip: PL061 GPIO chip @0x120d0000 registered
pl061_gpio 120d1000.gpio_chip: PL061 GPIO chip @0x120d1000 registered
pl061_gpio 120d2000.gpio_chip: PL061 GPIO chip @0x120d2000 registered
pl061_gpio 120d3000.gpio_chip: PL061 GPIO chip @0x120d3000 registered
pl061_gpio 120d4000.gpio_chip: PL061 GPIO chip @0x120d4000 registered
pl061_gpio 120d5000.gpio_chip: PL061 GPIO chip @0x120d5000 registered
pl061_gpio 120d6000.gpio_chip: PL061 GPIO chip @0x120d6000 registered
pl061_gpio 120d7000.gpio_chip: PL061 GPIO chip @0x120d7000 registered
pl061_gpio 120d8000.gpio_chip: PL061 GPIO chip @0x120d8000 registered
pl061_gpio 120d9000.gpio_chip: PL061 GPIO chip @0x120d9000 registered
pl061_gpio 120da000.gpio_chip: PL061 GPIO chip @0x120da000 registered
pl061_gpio 120db000.gpio_chip: PL061 GPIO chip @0x120db000 registered
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] No driver support for vblank timestamp query.
[drm] Initialized hisilicon 1.0.0 20200602 for hidrm on minor 0
brd: module loaded
libphy: hisi_femac_mii_bus: probed
libphy: Fixed MDIO Bus: probed
hisi-femac 10010000.ethernet: using random MAC address 6a:0c:10:b4:a9:54
Generic PHY 10011100.mdio:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=10011100.mdio:01, irq=POLL)
phy_id=0x001cc816, phy_mode=rmii
usbcore: registered new interface driver r8152
dwc3 100e0000.hidwc3_0: Failed to get clk 'ref': -2
xhci-hcd 100e0000.xhci_0: can't request region for resource [mem 0x100e0000-0x100effff]
xhci-hcd: probe of 100e0000.xhci_0 failed with error -16
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver xpad
hibvt_rtc 12080000.rtc: rtc core: registered 12080000.rtc as rtc0
hibvt_rtc 12080000.rtc: RTC driver for hibvt enabled
i2c /dev entries driver
hibvt-i2c 120b0000.i2c: hibvt-i2c0@100000hz registered
hibvt-i2c 120b1000.i2c: hibvt-i2c1@100000hz registered
hibvt-i2c 120b2000.i2c: hibvt-i2c2@100000hz registered
hibvt-i2c 120b3000.i2c: hibvt-i2c3@100000hz registered
hibvt-i2c 120b4000.i2c: hibvt-i2c4@100000hz registered
hibvt-i2c 120b5000.i2c: hibvt-i2c5@100000hz registered
hibvt-i2c 120b6000.i2c: hibvt-i2c6@100000hz registered
hibvt-i2c 120b7000.i2c: hibvt-i2c7@100000hz registered
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
himci: mmc host probe
himci: sdio_setup entry!
himci: mmc host probe
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 8GTF4R 7.27 GiB 
mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (250:0)
 mmcblk0: p1(boot) p2(kernel) p3(updater) p4(misc) p5(system) p6(vendor) p7(userdata)
himci: mmc host probe
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ashmem: initialized
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
hibvt_rtc 12080000.rtc: setting system clock to 1970-01-01 00:00:00 UTC (0)
[I/osal_cdev] register hdf class success
[I/osal_cdev] add cdev dev_mgr success

[I/hcs_blob_if] CheckHcsBlobLength: the blobLength: 21268, byteAlign: 1
[W/driver_loader] failed to load node, property is null, match attr is: linux_gpio_adapter
[I/linux_gpio_adapter] LinuxGpioInit: Enter
[I/gpio_core] GpioCntlrAdd: start:0 count:200
[I/linux_gpio_adapter] LinuxGpioInit: dev service: init success!
[I/device_node] policy is 0
[E/emmc_adapter_c] Hi35xxLinuxEmmcBind: entry!
[I/osal_cdev] add cdev HDF_PLATFORM_MMC_0 success

[I/hdf_watchdog_adapter] HdfWdtBind: entry
[I/hdf_watchdog_adapter] HdfWdtBind: dev service HDF_PLATFORM_WATCHDOG_0 init success!
[W/driver_loader] failed to load node, property is null, match attr is: hisilicon_hi35xx_rtc
[I/RTC_ADAPTER] HiRtcInit: Hdf dev service:HDF_PLATFORM_RTC init success
[I/hdf_uart_adapter] HdfUartBind: entry
[I/hdf_uart_adapter] HdfUartInit: entry
[I/osal_cdev] add cdev HDF_PLATFORM_UART_1 success

[I/hdf_uart_adapter] HdfUartBind: entry
[I/hdf_uart_adapter] HdfUartInit: entry
[W/driver_loader] failed to load node, property is null, match attr is: hdf_platform_i2c_manager
[I/i2c_core] I2cManagerBind: Enter!
[I/osal_cdev] add cdev HDF_PLATFORM_I2C_MANAGER success

[I/i2c_linux_adapter] LinuxI2cInit: Enter
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/i2c_linux_adapter] LinuxI2cParseAndInit: Enter
[I/i2c_core] I2cCntlrAdd: use default lock methods!
[I/device_node] policy is 0
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceBind: entry
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceInit: entry
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceBind: entry
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceInit: entry
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceBind: entry
[I/HDF_SPI_LINUX_ADAPTER] HdfSpiDeviceInit: entry
[E/sdio_adapter_c] Hi35xxLinuxSdioBind: entry!
[I/HDF_PWM_LINUX_ADAPTER] HdfPwmInit: entry
[I/HDF_PWM_LINUX_ADAPTER] HdfPwmInit: entry
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_LOG_TAG] load mipi_tx driver 1212!
[E/HDF_LOG_TAG] load mipi_tx driver successful!

[I/device_node] policy is 0
[E/HDF_LOG_TAG] failed to get device entry hdf_usb_pnp_notify_service
[E/driver_loader] failed to load node, deviceEntry is null
[E/devhost_service_clnt] failed to install driver hdf_usb_pnp_notify_service, ret = -203
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/sensor_device_manager_c] InitSensorDevManager: init sensor manager successfully
[I/osal_cdev] add cdev hdf_sensor_manager_ap success

[E/KMsgEngine] DoStartMessageRouter:Create local node ...
[I/KMsgEngine] Creating local node...
[I/KMsgEngine] Register default dispatcher...
[I/HDF_WIFI_CORE] ParseWlanChipsCompsConfig: driverName=hisi
[W/KMsgEngine] DoRegistService:Register service Node:0;Dispatcher:0;Service:1
[W/KMsgEngine] DoRegistService:Register service Node:0;Dispatcher:0;Service:2
[W/KMsgEngine] DoRegistService:Register service Node:0;Dispatcher:0;Service:3
[I/osal_cdev] add cdev hdfwifi success

[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_INPUT_DRV] HdfInputManagerInit: enter
[I/HDF_INPUT_DRV] HdfInputManagerInit: exit succ
[I/osal_cdev] add cdev hdf_input_host success

[I/HDF_LOG_TAG] HdfTouchDriverProbe: enter
[I/HDF_LOG_TAG] HdfTouchDriverProbe: main_touch exit succ
[I/osal_cdev] add cdev hdf_input_event1 success

[I/HDF_INPUT_DRV] HdfGoodixChipInit: enter
[I/HDF_LOG_TAG] ChipMatchCheck: boardNode's father name = touch0, chipNode's grandpa name = touch0
hibvt-i2c 120b6000.i2c: wait Timeout!
hibvt-i2c 120b6000.i2c: wait idle timeout, RIS: 0x410, SR: 0xa0000
[E/HDF_LOG_TAG] InputI2cRead: i2c read err
[E/HDF_INPUT_DRV] ChipDetect: read chip version failed
[E/devhost_service_clnt] failed to install driver hdf_touch_gt911_service, ret = -204
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_INPUT_DRV] LoadCachedHid: exit
[I/device_node] policy is 0
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_LOG_TAG] RegisterPanel: register success
[I/HDF_LOG_TAG] Icn9700EntryInit: exit succ
[I/device_node] policy is 0
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_DISP] MipiDsiInit:pixelClk = 31546, phyDataRate = 379
[I/HDF_DISP] RegisterDispCtrl: success
[I/device_node] policy is 0
[W/driver_loader] failed to load node, property is null, match attr is: 
[I/HDF_DISP] EsdCheckInit none of panels support esd
[I/osal_cdev] add cdev hdf_disp success

[W/driver_loader] failed to load node, property is null, match attr is: 
[I/osal_cdev] add cdev sample_service success

[W/driver_loader] failed to load node, property is null, match attr is: 
[I/osal_cdev] add cdev HDF_TEST success

[W/driver_loader] failed to load node, property is null, match attr is: 
[I/sensor_device_manager_c] AddSensorDevice: register sensor device name[sensor_test] success
[I/hdf_sensor_test_c] InitSensorDriverTest: init sensor test driver success
[I/device_node] policy is 0
[E/uart_test_c] UartTestBind: success
[E/uart_test_c] UartTestInit: success
[W/driver_loader] failed to load node, property is null, match attr is: PLATFORM_MIPI_DSI_TEST
[E/sdio_test_c] SdioTestBind: Sdio_TEST service init success!
[E/sdio_test_c] SdioTestFillConfig: busNum:2, funcNum:1, vendorId:0x296, deviceId:0x5347.
[E/sdio_test_c] SdioTestInit: success
[E/emmc_test_c] EmmcTestBind: EMMC_TEST service init success!
[E/emmc_test_c] EmmcTestFillConfig: busNum:0, hostId:0.
[E/emmc_test_c] EmmcTestInit: success
[E/spi_test_c] SpiTestInit: success
[I/osal_cdev] add cdev I2C_TEST success

[W/driver_loader] failed to load node, property is null, match attr is: WATCHDOG_TEST
[E/pwm_test_c] PwmTestBind: success
[E/pwm_test_c] PwmTestInit: success
clk: Not disabling unused clocks
ALSA device list:
  No soundcards found.
Waiting 10 sec before mounting root device...
himci: card disconnected!
EXT4-fs (mmcblk0p5): warning: mounting unchecked fs, running e2fsck is recommended
EXT4-fs (mmcblk0p5): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:5.
devtmpfs: mounted
Freeing unused kernel memory: 1024K
Run /init as init process
random: init: uninitialized urandom read (40 bytes read)
himci: card connected!
random: init: uninitialized urandom read (40 bytes read)
init: init first stage started!
init: Using Android DT directory /proc/device-tree/firmware/android/
init: [libfs_mgr]ReadDefaultFstab(): failed to find device default fstab
init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/platform/soc/10100000.himci.eMMC/by-name/vendor
EXT4-fs (mmcblk0p6): mounted filesystem without journal. Opts: barrier=1,inode_readahead_blks=8
init: [libfs_mgr]__mount(source=/dev/block/platform/soc/10100000.himci.eMMC/by-name/vendor,target=/vendor,type=ext4)=0: Success
init: Failed to open device-mapper: No such file or directory
init: Skipped setting INIT_AVB_VERSION (not in recovery mode)
random: init: uninitialized urandom read (40 bytes read)
init: Loading SELinux policy
SELinux:  policy capability network_peer_controls=1
SELinux:  policy capability open_perms=1
SELinux:  policy capability extended_socket_class=1
SELinux:  policy capability always_check_network=0
SELinux:  policy capability cgroup_seclabel=0
SELinux:  policy capability nnp_nosuid_transition=1
audit: type=1403 audit(13.390:2): auid=4294967295 ses=4294967295 lsm=selinux res=1
selinux: SELinux: Loaded policy from /vendor/etc/selinux/precompiled_sepolicy

selinux: SELinux: Loaded file_contexts

init: init second stage started!
init: Using Android DT directory /proc/device-tree/firmware/android/
selinux: SELinux: Loaded file_contexts

init: Running restorecon...
init: Couldn't load property file '/product_services/build.prop': open() failed: No such file or directory: No such file or directory
init: Couldn't load property file '/factory/factory.prop': open() failed: No such file or directory: No such file or directory
init: Setting product property ro.product.brand to 'HisparkTaurus' (from ro.product.odm.brand)
init: Setting product property ro.product.device to 'hi3516dv300' (from ro.product.odm.device)
init: Setting product property ro.product.manufacturer to 'Hisilicon' (from ro.product.odm.manufacturer)
init: Setting product property ro.product.model to 'Hi3516DV300' (from ro.product.odm.model)
urandom_read: 4 callbacks suppressed
random: init: uninitialized urandom read (40 bytes read)
random: ueventd: uninitialized urandom read (40 bytes read)
random: apexd: uninitialized urandom read (40 bytes read)
ueventd: ueventd started!
selinux: SELinux: Loaded file_contexts

apexd: Bootstrap subcommand detected
ueventd: Parsing file /ueventd.rc...
ueventd: Parsing file /vendor/ueventd.rc...
apexd: Scanning /system/apex for embedded keys
apexd: Scanning /product/apex for embedded keys
apexd: ... does not exist. Skipping
ueventd: /vendor/ueventd.rc: 14: invalid gid 'net_bt_stack'
ueventd: Parsing file /odm/ueventd.rc...
ueventd: Unable to read config file '/odm/ueventd.rc': open() failed: No such file or directory
apexd: Scanning /system/apex looking for APEX packages.
apexd: Found /system/apex/com.android.runtime-hos.debug
apexd: Successfully bind-mounted flattened package /system/apex/com.android.runtime-hos.debug on /apex/com.android.runtime@1
ueventd: Parsing file /ueventd.unknown.rc...
ueventd: Unable to read config file '/ueventd.unknown.rc': open() failed: No such file or directory
apexd: Activated 1 packages. Skipped: 0
apexd: Bootstrapping done
ueventd: [libfs_mgr]ReadDefaultFstab(): failed to find device default fstab
EXT4-fs (mmcblk0p7): Ignoring removed nomblk_io_submit option
EXT4-fs (mmcblk0p7): recovery complete
EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
binder: 69:69 ioctl 4010620d bede0aa8 returned -22
binder: 68:68 ioctl 4010620d be90aa58 returned -22
audit: type=1400 audit(14.910:3): avc:  denied  { set_context_mgr } for  pid=70 comm="samgr" scontext=u:r:samgr:s0 tcontext=u:r:samgr:s0 tclass=binder permissive=1
[W/HDF_WIFI_CORE] Driver HdfWiFi initing...
[E/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Config Hi3516DV300 SDIO bus 2
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x12090000] 0000 to 0080
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f0008] 06b1 to 0601
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f000c] 05e1 to 0501
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f0010] 05e1 to 0501
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f0014] 05e1 to 0501
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f0018] 05e1 to 0501
[W/HDF_LOG_TAG] ConfigHi3516DV300SDIO: Change register[0x112f001c] 05e1 to 0501
[W/HDF_WIFI_CORE] HdfWlanPowerOnProcess:Chip power on!
[W/HDF_WIFI_CORE] HdfWlanResetProcess:Chip reset success!
himci: card disconnected!
himci: card connected!
himci: card disconnected!
himci: card connected!
himci_wait_cmd:259: 
Other CMD is running,please operate cmd again!

himci_set_cclk:361: 
set card clk divider is failed!

himci_wait_cmd:259: 
Other CMD is running,please operate cmd again!

init: [libfs_mgr]check_fs(): unmount(/data) succeeded
init: [libfs_mgr]Not running /system/bin/e2fsck on /dev/block/mmcblk0p7 (executable not in system image)
init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/platform/soc/10100000.himci.eMMC/by-name/userdata
init: [libfs_mgr]Reserved blocks 25600 is too large; capping to 7168
init: [libfs_mgr]Unable to set the number of reserved blocks on /dev/block/platform/soc/10100000.himci.eMMC/by-name/userdata because /system/bin/tune2fs is missing
EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: barrier=1,data=ordered,noauto_da_alloc
init: [libfs_mgr]__mount(source=/dev/block/platform/soc/10100000.himci.eMMC/by-name/userdata,target=/data,type=ext4)=0: Success
init: Parsing file /product/etc/init...
init: Unable to read config file '/product/etc/init': open() failed: No such file or directory
init: Parsing file /product_services/etc/init...
init: Unable to read config file '/product_services/etc/init': open() failed: No such file or directory
hi_osal: loading out-of-tree module taints kernel.
hi_osal: unknown parameter '||' ignored
hi_osal: unknown parameter 'report_error' ignored
Module himedia: init ok
Hisilicon Media Memory Zone Manager
hi_osal 1.0 init success!
enter hi_irq_probe 
hi_irq init ok. ver=Jun 22 2021, 15:29:26.
hi_proc: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint

==========chip: hi3516dv300==========

==========sensor0: imx335==========

==========sensor1: NULL==========
FUNC:parse_sensor_clock line:249  SNS:[NULL] is not supported !
FUNC:parse_sensor_bus_type line:203  SNS:[NULL] is not supported !
FUNC:parse_sensor_index line:108  SNS prefix:[g_cmos_yuv_flag] is not supported !
load sys.ko for Hi3516CV500...OK!
load tde.ko for Hi3516CV500...OK!
load vo_dev.ko for Hi3516CV500...OK!
[drm:drm_check_dumb_phy_addr] *ERROR* drm_check_dumb_phy_addr, addr_start-addr_end [0xa8020000-0xa8ff2000]
load hifb.ko OK!
load hdmi.ko for Hi3516CV500...OK!
load mipi_rx driver successful!
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b

CPU: 1 PID: 1 Comm: init Tainted: P           O      4.19.155+ #1
Hardware name: Generic DT based system
[<c0110a30>] (unwind_backtrace) from [<c010c8cc>] (show_stack+0x10/0x14)
[<c010c8cc>] (show_stack) from [<c08495bc>] (dump_stack+0x88/0xb4)
[<c08495bc>] (dump_stack) from [<c011a8c8>] (panic+0xf4/0x27c)
[<c011a8c8>] (panic) from [<c011e310>] (complete_and_exit+0x0/0x1c)
[<c011e310>] (complete_and_exit) from [<00000000>] (  (null))
CPU0: stopping
CPU: 0 PID: 47 Comm: kworker/0:2 Tainted: P           O      4.19.155+ #1
Hardware name: Generic DT based system
Workqueue: events_freezable mmc_rescan
[<c0110a30>] (unwind_backtrace) from [<c010c8cc>] (show_stack+0x10/0x14)
[<c010c8cc>] (show_stack) from [<c08495bc>] (dump_stack+0x88/0xb4)
[<c08495bc>] (dump_stack) from [<c010ea48>] (ipi_cpu_stop+0x60/0x7c)
[<c010ea48>] (ipi_cpu_stop) from [<c010e9e8>] (ipi_cpu_stop+0x0/0x7c)
[<c010e9e8>] (ipi_cpu_stop) from [<c0c187ec>] (0xc0c187ec)
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
 ]---

[END] 2021/6/22 16:12:23

OpenHarmony/kernel_linux_patches

内容风险标识

评论 (3)

OpenHarmony/kernel_linux_patches .gitee-modal { width: 500px !important; }

内容风险标识