ExpressLRS 发行版

1.1.0

2021-09-07 16:24

###  **ExpressLRS V1.1.0 Release Notes**

### The important stuff

- Arming must be on AUX1 for safety and feature reasons, having this fixed allows us to maintain small packet sizes and deliver better aux channel options
- Be sure to flash both the TX and RX
expresslrs.org/quick-start/
### Enhancements

NA
### Bugfixes

- Enables fan on Happymodel ES24TX Slim #781
- Fix NamimnoRC backpack/WiFi upload to also include bootloader upload #802
- Removes 25hz 2.4GHz from ELRS.lua #810
- Fix some users not being able to flash 1.0.0 or 1.0.1 to EP1/2 RXs #862
- Remove low power LUA selection from relevant TX modules e.g. the HM Slim Pro is limited to a minimum of 25mW #865
### Hardware Targets:

- 2.4GHz
Happymodel ES24TX Slim Pro #863
- 915-868MHz
NA
### A note on versioning

The versioning scheme chosen by the ExpressLRS devs is based on the semantic versioning scheme. https://semver.org/

Where a version is defined as “major.minor.patch”
major = major new feature and/or incompatible changes
minor = minor features or enhancements and/or new targets
patch = bug-fixes

最后提交信息为： update version number to v1.1.0

1.0.1

1d543bc

2021-08-04 10:02

ExpressLRS V1.0.1 Release Notes

**The important stuff**

- Arming must be on AUX1 for safety and feature reasons, having this fixed allows us to maintain small packet sizes and deliver better aux channel options
- Be sure to flash both the TX and RX 
expresslrs.org/quick-start/

**Enhancements**

- Unlocked high power (1W) by default on the Namimno TXes (which come with a fan pre-installed)
- Added config for building ESPbackpack firmware with alternate pins that work with ESP-01 modules

**Bugfixes**

- Limited Namimno TXes to 25mW minimum (lowest hardware supported power level)
- Fixed issue with not being able to connect to the ESPbackpack access point reliably
- Fixed WebSocket info prints on ESPbackpack
- Fix “RX Serial not found” when attempting to flash via passthrough on Omnibus F4 FCs
- Fix WIFI updating (directly from the Configurator) on ESP32 targets

**Hardware Targets:** 
 **2.4GHz**

- HGLRC Hermes TX via UART and WIFI)
- HGLRC Hermes RX via UART, WIFI, and Passthrough)
- BETAFPV Nano TX via WIFI
- BETAFPV Nano RX via WIFI

**915-868MHz**

- HGLRC Hermes RX (via UART, WIFI, and Passthrough)
- BETAFPV Nano TX via WIFI
- BETAFPV Nano RX via WIFI

最后提交信息为： HGLRC Targets (#734)

1.0.0

d9d30e7

2021-07-22 14:25

ExpressLRS V1.0.0 Release Notes

**ExpressLRS V1.0.0 Release Notes** 
Lots of great work has gone into the first major release of ExpressLRS. The number of users and contributors has grown rapidly allowing for some awesome features to be added.

[https://expresslrs.github.io/Docs/](http://)

**ExpressLRS 1.0.0 is finally here... 1st EVER RELEASE!! https://youtu.be/XbKpWI0YJ5I**

**The important stuff** 
Arming must be on AUX1 for safety and feature reasons, having this fixed allows us to maintain small packet sizes and deliver better aux channel options
Be sure to flash both the TX and RX
expresslrs.org/quick-start/
Update your LUA script
 **ExpressLRS Firsts** 
200Hz 900MHz LoRa
250 and 500Hz 2.4GHz LoRa
SMD antenna
SPI LoRa RX integration with Betaflight
Bind Passphrase for seamless multi-binding
 **Features** 
Optimized for receiver sensitivity resulting in exceptional range
As low as 2ms packet interval (500Hz)
Low latency, low jitter, phenomenal timing consistency
Highly configurable RF power, packet rate, and telemetry ratios for bleeding edge speed, crazy range, or anything in between.
Support for both Team2.4, Team900 and Team433 within the same codebase
Antenna diversity
Low cost hardware available from a variety of manufacturers with unique designs
Works with anything that handles CRSF protocol: Betaflight, iNav, Ardupilot, Emuflight, vJoySerialFeeder, etc
Receivers as small as 10mm x 10mm x 0.6mm, 0.44g with antenna
 **Telemetry Support** 
Link Statistics, Voltage, Current, Battery Capacity, Attitude and Rate, Flight Mode, GPS Position, Altitude, Heading, Speed and Satellites etc.
MSP passthrough for Betaflight Lua scripts etc.
Selectable telemetry bandwidth allocation from none to 10kbit
 **Quality of life** 
ExpressLRS Configurator flashing utility https://github.com/ExpressLRS/ExpressLRS-Configurator/releases
Conventional binding support or Passphrase multi-binding
Button-less passthrough for easy firmware updates when connected to a flight controller
WiFi firmware updates
No inverted UART needed on flight controller
 **Hardware Targets:** 
 **2.4GHz** 
Happymodel TX/RX
BETAFPV TX/RX
NamimnoRC TX/RX
SIYI FM30 TX/RX
ImmersionRC Ghost TX/RX
ExpressLRS DIY TX/RX https://github.com/ExpressLRS/ExpressLRS-Hardware
 **915-868MHz** 
Happymodel TX/RX
BETAFPV TX/RX
NamimnoRC TX/RX
NeutronRC RX
FrSky R9 TX/RX
ExpressLRS DIY TX/RX https://github.com/ExpressLRS/ExpressLRS-Hardware
 **AIO Flight Controllers** 
Compatible with the SPI RX found on the Happymodel and SP Racing flight controllers

**Communities** 
 **Discord** 
Here you will find a community of nearly 4k users and a heap of tech talk, both software and hardware hacking. This is also the best place to get real time support for any issues. https://discord.gg/dS6ReFY

**Facebook** 
A great place to show and tell your achievements on the race track or a long range flight.
https://www.facebook.com/groups/636441730280366

**GitHub** 
This is where you can discuss code additions and changes. ELRS is still in the early days of development with big plans for future releases…

最后提交信息为： add betafpv900 and betafpv2400 hardware support (#646)

预览版本

1.0.0-RC9

6358aa6

2021-07-09 10:54

ExpressLRS V1.0.0 RC9 Release