代码拉取完成，页面将自动刷新
After running make command, there will be two modules:
The fist module is ou fake ethernet driver, the second one is used to create a plateform device that matches our first module. This way, one can avoid updating the devicetree.
# insmod ./fake-eth.ko
# insmod ./eth-ins.ko
After loading both modules, one can print debug message, and see something like below:
#dmesg
[146626.222072] fake-eth added
[146689.422000] fake-fake removed
[146698.060074] fake eth device initialized
[146698.060285] fake-eth added
[146698.087297] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Before loading the module, there were no eth0
$ ifconfig -a
enp3s0f1 Link encap:Ethernet HWaddr 34:97:f6:ba:5e:d7
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:49727 errors:0 dropped:0 overruns:0 frame:0
TX packets:49727 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:8431650 (8.4 MB) TX bytes:8431650 (8.4 MB)
[...]
After loading modules,
$ ifconfig -a
enp3s0f1 Link encap:Ethernet HWaddr 34:97:f6:ba:5e:d7
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:49727 errors:0 dropped:0 overruns:0 frame:0
TX packets:49727 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:8431650 (8.4 MB) TX bytes:8431650 (8.4 MB)
[...]
One can also configure the interface like ifconfig eth0 192.168.1.45,
and then
$ ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:192.168.1.45 Bcast:192.168.1.255 Mask:255.255.255.0
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
此处可能存在不合适展示的内容，页面不予展示。您可通过相关编辑功能自查并修改。
如您确认内容无涉及 不当用语 / 纯广告导流 / 暴力 / 低俗色情 / 侵权 / 盗版 / 虚假 / 无价值内容或违法国家有关法律法规的内容，可点击提交进行申诉，我们将尽快为您处理。
马建仓 AI 助手