代码拉取完成，页面将自动刷新
Link Layer Discovery Protocol (LLDP) Agent with
Data Center Bridging (DCB) for Intel(R) Network Connections
===========================================================
April 7, 2010
Contents
========
- Background
- Requirements
- Functionality
- How To Build a DCB capable system
- Setup
- Operation
- Testing
- dcbtool Overview
- FAQ
- Known Issues
- License
- Support
Background on DCB support
=========================
In the 2.4.x kernel, qdiscs were introduced. The rationale behind this effort
was to provide QoS in software, as hardware did not provide the necessary
interfaces to support it. In 2.6.23, Intel introduced the idea of multiqueue
support into the qdisc layer. This provides a mechanism to map the software
queues in the qdisc structure into multiple hardware queues in underlying
devices. In the case of Intel adapters, this mechanism is used to map
qdisc queues onto the queues within the hardware controllers.
Within the Data Center, the perception is that traditional Ethernet is
subject to high latency and is prone to losing frames, rendering it
unacceptable for storage applications
In an effort to address these issues, Intel and a host of industry leaders have
been working on addressing these problems. Specifically, within the IEEE 802.1
standards body there are a number of task forces working on enhancements to
address these concerns. Listed below are the applicable standards:
Enhanced Transmission Selection: IEEE 802.1Qaz
Lossless Traffic Class
Priority Flow Control: IEEE 802.1Qbb
Congestion Notification: IEEE 802.1Qau
DCB Capability exchange protocol (DCBX): IEEE 802.1Qaz
The software solution that is being released represents Intel's implementation
of these efforts. It is worth noting that many of these standards have not been
ratified - this is a pre-standards release, so users are advised to check
Sourceforge often. While we have worked with some of the major ecosystem
vendors in validating this release, there are many vendors which still have
solutions in development. As these solutions become available and standards get
ratified, we will work with ecosystem partners and the standards body to ensure
that the Intel solution works as expected.
Requirements
============
- Linux kernel version 2.6.29 or later.
- 2.6.29 or newer version of the "iproute2" package should be downloaded and
installed in order to obtain a multi-queue aware version of the 'tc' utility.
Check for new versions at:
http://www.linuxfoundation.org/en/Net:Iproute2
- Version 2.5.33 of Flex should be installed (to support iproute2).
Flex source can be obtained from http://flex.sourceforge.net/
- An up to date netlink library needs to be installed in order to compile
lldpad.
- Version 1.3.2 or greater of libconfig must be installed.
libconfig source can be obtained from http://www.hyperrealm.com/libconfig/
- For DCB features - a driver which supports the dcbnl rtnetlink interface
in the kernel (e.g. the ixgbe driver for 82598-based or 82599-based Intel
adapters).
Functionality
=============
lldpad
- Executes the Link Layer Discovery Protocol (LLDP) over all supported
interfaces.
- Executes the DCB capabilities exchange protocol (DCBX) to exchange DCB
configuration with the peer device using LLDP on support interfaces.
- Supports the versions of the DCB capabilities exchange protocol
described here:
- version 1
<http://download.intel.com/technology/eedc/dcb_cep_spec.pdf>
and here:
- version 2
<http://www.ieee802.org/1/files/public/docs2008/az-wadekar-dcbx-
capability-exchange-discovery-protocol-1108-v1.01.pdf>
- Retrieves and stores LLDP and DCB configuration to a configuration file.
- Controls the DCB settings of the network driver based on the
operation of the DCB capabilities exchange protocol. Interaction with
a supporting network driver is achieved via DCB operations added to the
rtnetlink interface in kernel 2.6.29.
- Supports the following DCB features: Priority Group,
Priority Flow Control, FCoE, and FCoE Logical Link Status.
- Provides an interface for client applications to query and configure
DCB features. Generates client interface events when the operational
configuration or state of a feature changes.
lldptool
-
dcbtool
- Interacts with lldpad via the client interface.
- Queries the state of the local, operational and peer configuration for
the supported DCB features.
- Supports configuring the supported DCB features.
- Interactive mode allows multiple commands to be entered interactively,
as well as displaying event messages.
- Enables or disables DCB for an interface.
How To Build a DCB-Capable System
=================================
Linux kernel install:
---------------------
1. Requires 2.6.29 kernel.
2. Untar and make the kernel. Listed below are the required kernel options:
Required configuration options:
From make menuconfig
a. In Networking support -> Networking options, enable Data Center Bridging
b. In Networking support -> Networking options -> QoS and/or fair queuing,
enable:
Hardware Multiqueue-aware Multi Band Queuing (MULTIQ)
Multi Band Priority Queueing (PRIO)
Elementary classification ( BASIC )
Universal 32bit comparisons w/ hashing (U32)
Extended Matches and make sure U32 key is selected
Actions -> SKB Editing
c. To enable ixgbe driver support for DCB,
In Device Drivers -> Network device support -> Ethernet (10000 Mbit)
enable Intel(R) 10GbE PCI Express adapters support and the
Data Center Bridging (DCB) Support option
3. Build the kernel.
4. lldpad requires updated kernel header files to compile.
Create a link from /usr/include/linux to the location of the kernel source
include files. For example:
ln -s /usr/src/kernels/linux-2.x.xx.x/include/linux /usr/include/linux
lldpad Application Install
--------------------------
1. Download iproute2 from the web.
See: http://www.linuxfoundation.org/en/Net:Iproute2
Please ensure that you use the version that corresponds to the kernel
version that you are using. Follow the build/installation instructions
in the README. Typically, the commands:
./configure; make; make install
will work.
2. Download the latest version of the lldpad-x.y.z tarball from the e1000
project in Sourceforge and untar it.
Check to see that the following libraries are installed; install them if
they are not present.
libtool; libconfig-devel; libnl-devel; readline-devel
Go into the lldpad-x.y.z directory and run the following commands
./bootstrap.sh; ./configure --prefix=/usr; make; make install
This will build and install 'lldpad', 'lldptool' and 'dcbtool' to /usr/sbin,
make the '/var/lib/lldpad' directory (default location of
the lldpad.conf file) and setup lldpad to run as a system service using the
chkconfig program. Verify that the lldpad service is working as expected
with the 'service lldpad status' command. If the service is not on, issue
the command 'service lldpad start'
Note (known issue): if the --prefix option is not supplied to the
configure script, then the default install location of 'lldpad', 'lldptool'
and 'dcbtool' is /usr/local/sbin. This does not match the 'lldpad' script
installed in /etc/init.d, which is coded to start lldpad from
/usr/sbin/lldpad.
lldpad will create the lldpad.conf file if it does not exist.
For development purposes, 'lldpad' can be run directly from the build
directory.
Options
-------
lldpad has the following command line options:
-h show usage information
-f configfile use the specified file as the config file instead of
the default file - /var/lib/lldpad/lldpad.conf
-d run lldpad as a daemon
-v show lldpad version
-k terminate current running lldpad
-s remove lldpad state records
SETUP:
======
1. Load the ixgbe module.
2. Verify lldpad service is functional.
If lldpad was installed, do "service lldpad status" to check, "service
lldpad start" to start.
Or, run "lldpad -d" from the command line to start.
3. Enable DCB on the selected ixgbe port:
dcbtool sc ethX dcb on
4. The dcbtool command can be used to query and change the DCB configuration
(ie., various percentages to different queues). Use dcbtool -h to see a
list of options.
DCBX Operation
==============
lldpad and dcbtool can be used to configure a DCB capable driver, such as
the ixgbe driver, which supports the rtnetlink DCB interface. Once the
DCB features are configured, the next step is to classify traffic to be
identified with an 802.1p priority and the associated DCB features.
This can be done using a couple different methods.
1. qdisc and filter method
The skbedit action mechanism can be used in a tc filter to classify traffic
patterns to a specific queue_mapping value from 0-7. The ixgbe driver will
place traffic with a given queue_mapping value onto the corresponding hardware
queue and tag the outgoing frames with the corresponding 802.1p priority value.
Set up the multi-queue qdisc for the selected interface:
# tc qdisc add dev ethX root handle 1: multiq
Setting the queue_mapping in a TC filter allows the ixgbe driver to classify a
packet into a queue. Here is an example of a filter to cause iSCSI traffic
(running on the well known port number 3260) to be tagged with priority 4.
# tc filter add dev ethX protocol ip parent 1: u32 match ip dport 3260 \
0xffff action skbedit queue_mapping 4
# tc filter add dev ethX protocol ip parent 1: u32 match ip sport 3260 \
0xffff action skbedit queue_mapping 4
Here is an example that sets up a filter based on EtherType. In this example,
the EtherType is 0x8906.
# tc filter add dev ethX protocol 802_3 parent 1: handle 0xfc0e basic match \
'cmp(u16 at 12 layer 1 mask 0xffff eq 35078)' action skbedit queue_mapping 3
2. VLAN egress map method
Alternatively, traffic can be classified by configuring the egress map of a
VLAN interface. For example, if iSCSI traffic is desired to be on priority 4
and VLAN 101 is dedicated for iSCSI, then the following configuration could
be performed to map the skb_priorities on VLAN 101 to the 802.1p priority 4.
# vconfig set_egress_map ethX.101 0 4
# vconfig set_egress_map ethX.101 1 4
# vconfig set_egress_map ethX.101 2 4
...
# vconfig set_egress_map ethX.101 7 4
Note: since DCB features use the 802.1p priority in the VLAN tag to distinguish
traffic, it is expected that traffic in a DCB network will need to be on a
tagged VLAN.
Testing
=======
To test in a back-to-back setup, use the following tc commands to setup the
qdisc and filters for TCP ports 5000 through 5007. Then use a tool, such as
iperf, to generate UDP or TCP traffic on ports 5000-5007.
Statistics for each queue of the ixgbe driver can be checked using the
ethtool utility: ethtool -S ethX
# tc qdisc add dev ethX root handle 1: multiq
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5000 0xffff action skbedit queue_mapping 0
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5000 0xffff action skbedit queue_mapping 0
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5001 0xffff action skbedit queue_mapping 1
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5001 0xffff action skbedit queue_mapping 1
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5002 0xffff action skbedit queue_mapping 2
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5002 0xffff action skbedit queue_mapping 2
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5003 0xffff action skbedit queue_mapping 3
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5003 0xffff action skbedit queue_mapping 3
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5004 0xffff action skbedit queue_mapping 4
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5004 0xffff action skbedit queue_mapping 4
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5005 0xffff action skbedit queue_mapping 5
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5005 0xffff action skbedit queue_mapping 5
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5006 0xffff action skbedit queue_mapping 6
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5006 0xffff action skbedit queue_mapping 6
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip dport 5007 0xffff action skbedit queue_mapping 7
# tc filter add dev ethX protocol ip parent 1: \
u32 match ip sport 5007 0xffff action skbedit queue_mapping 7
dcbtool Overview
=================
dcbtool is used to query and set the DCB settings of a DCB capable Ethernet
interface. It connects to the client interface of lldpad to perform these
operations. dcbtool will operate in interactive mode if it is executed
without a command. In interactive mode, dcbtool also functions as an event
listener and will print out events received from lldpad as they arrive.
SYNOPSIS
dcbtool -h
dcbtool -v
dcbtool [-rR]
dcbtool [-rR] [command] [command arguments]
OPTIONS
-h shows the dcbtool usage message
-v shows dcbtool version information
-r displays the raw lldpad client interface messages as well as the
readable output.
-R displays only the raw lldpad client interface messages
COMMANDS
help shows the dcbtool usage message
ping test command. The lldpad daemon responds with "PONG" if the
client interface is operational.
license
displays dcbtool license information
quit exits from interactive mode
The following commands interact with the lldpad daemon to manage the dae-
mon and DCB features on DCB capable interfaces.
lldpad general configuration commands:
------------------------------------
<gc|go> dcbx
gets the configured or operational version of the DCB capabili-
ties exchange protocol. If different, the configured version
will take effect (and become the operational version) after lldpad
is restarted.
sc dcbx v:[1|2]
sets the version of the DCB capabilities exchange protocol which
will be used the next time lldpad is started. The default version
is 2. Changes take effect on next lldpad restart.
Information about version 1 can be found at:
<http://download.intel.com/technology/eedc/dcb_cep_spec.pdf>
Information about version 2 can be found at:
<http://www.ieee802.org/1/files/public/docs2008/az-wadekar-dcbx-
capability-exchange-discovery-protocol-1108-v1.01.pdf>
DCB per-interface commands:
---------------------------
gc <ifname> <feature>
gets configuration of feature on interface ifname.
go <ifname> <feature>
gets operational status of feature on interface ifname.
gp <ifname> <feature>
gets peer configuration of feature on interface ifname.
sc <ifname> <feature> <args>
sets the configuration of feature on interface ifname.
feature may be one of the following:
------------------------------------
dcb DCB state of the port
pg priority groups
pfc priority flow control
app:<subtype>
application specific data
ll:<subtype>
logical link status
subtype can be:
---------------
0|fcoe Fiber Channel over Ethernet (FCoE)
args can include:
-----------------
e:<0|1>
controls feature enable
a:<0|1>
controls whether the feature is advertised via DCBX to the peer
w:<0|1>
controls whether the feature is willing to change its opera-
tional configuration based on what is received from the peer
[feature specific args]
arguments specific to a DCB feature
Feature specific arguments for dcb:
-----------------------------------
on|off enable or disable DCB for the interface. The go and gp commands
are not needed for the dcb feature. Also, the enable, advertise
and willing parameters are not required.
Feature specific arguments for pg:
----------------------------------
pgid:xxxxxxxx
Priority group ID for the 8 priorities. From left to right
(priorities 0-7), x is the corresponding priority group ID
value, which can be 0-7 for priority groups with bandwidth allo-
cations or f (priority group ID 15) for the unrestricted prior-
ity group.
pgpct:x,x,x,x,x,x,x,x
Priority group percentage of link bandwidth. From left to right
(priority groups 0-7), x is the percentage of link bandwidth
allocated to the corresponding priority group. The total band-
width must equal 100%.
uppct:x,x,x,x,x,x,x,x
Priority percentage of priority group bandwidth. From left to
right (priorities 0-7), x is the percentage of priority group
bandwidth allocated to the corresponding priority. The sum of
percentages for priorities which belong to the same priority
group must total 100% (except for priority group 15).
strict:xxxxxxxx
Strict priority setting. From left to right (priorities 0-7), x
is 0 or 1. 1 indicates that the priority may utilize all of the
bandwidth allocated to its priority group.
up2tc:xxxxxxxx
Priority to traffic class mapping. From left to right (priori-
ties 0-7), x is the traffic class (0-7) to which the priority is
mapped. (This setting is ignored for Intel 82598-based
adapters.)
Feature specific arguments for pfc:
-----------------------------------
pfcup:xxxxxxxx
Enable/disable priority flow control. From left to right (pri-
orities 0-7), x is 0 or 1. 1 indicates that the corresponding
priority is configured to transmit priority pause.
Feature specific arguments for app:< subtype>:
----------------------------------------------
appcfg:xx
xx is a hexadecimal value representing an 8 bit bitmap where bits
set to 1 indicate the priority which frames for the applications
specified by subtype should use. The lowest order bit maps to
priority 0.
Feature specific arguments for ll:<subtype>:
--------------------------------------------
status:[0|1]
For testing purposes, the logical link status may be set to 0 or
1. This setting is not persisted in the configuration file.
EXAMPLES
Enable DCB on interface eth2
dcbtool sc eth2 dcb on
Assign priorities 0-3 to priority group 0, priorities 4-6 to priority
group 1 and priority 7 to the unrestricted priority. Also, allocate
25% of link bandwidth to priority group 0 and 75% to group 1.
dcbtool sc eth2 pg pgid:0000111f pgpct:25,75,0,0,0,0,0,0
Enable transmit of Priority Flow Control for priority 3 and assign FCoE
to priority 3.
dcbtool sc eth2 pfc pfcup:00010000
dcbtool sc eth2 app:0 appcfg:08
FAQ
===
- How did Intel verify their DCB solution?
Answer - The Intel solution is continually evolving as the relevant
standards become solidified and more vendors introduce DCB capable systems.
That said, we initially used test automation to verify the DCB state
machine. As the state machine became more robust and we had DCB capable
hardware, we began to test back to back with our adapters. Finally, we
introduced DCB capable switches in our test bed.
Known Issues
============
- Prior to kernel 2.6.26, TSO will be disabled when the driver is put into DCB
mode.
- A TX unit hang may be observed when link strict priority is set when a large
amount of traffic is transmitted on the link strict priority.
License
=======
lldpad, lldptool and dcbtool - LLDP daemon with DCB support and command line
utilities for LLDP and DCB configuration
Copyright(c) 2007-2010 Intel Corporation.
Portions of lldpad, lldptool and dcbtool are based on:
hostapd-0.5.7
Copyright (c) 2004-2007, Jouni Malinen <j@w1.fi>
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
version 2, as published by the Free Software Foundation.
This program is distributed in the hope it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc.,
51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
The full GNU General Public License is included in this distribution in
the file called "COPYING".
Support
=======
Contact Information:
LLDP-devel Mailing List <lldp-devel@open-lldp.org>
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
此处可能存在不合适展示的内容，页面不予展示。您可通过相关编辑功能自查并修改。
如您确认内容无涉及 不当用语 / 纯广告导流 / 暴力 / 低俗色情 / 侵权 / 盗版 / 虚假 / 无价值内容或违法国家有关法律法规的内容，可点击提交进行申诉，我们将尽快为您处理。
马建仓 AI 助手