3 Star 19 Fork 8

SeekFree / 逐飞科技基于MM32SPIN27的智能车BLDC开源项目

加入 Gitee
与超过 1200万 开发者一起发现、参与优秀开源项目,私有仓库也完全免费 :)
免费加入
克隆/下载
贡献代码
同步代码
取消
提示: 由于 Git 不支持空文件夾,创建文件夹后会生成空的 .keep 文件
Loading...
README
GPL-3.0

逐飞基于MM32SPIN27PS的无刷驱动方案开源啦!

逐飞基于MM32SPIN27PS的无刷驱动开源项目

输入图片说明

基于灵动MM32SPIN27的无刷电机驱动板

各参赛同学们好,现在应该都看过规则啦,第十七届智能车竞赛的极速越野组允许使用无刷电机,并且这个赛题的主控和无刷驱动主控方案都限定使用赞助商“灵动微电子”的MCU,逐飞科技作为灵动微电子的大学计划官方合作伙伴,受灵动微电子委托,在去年12月1日就发布了基于MM32的极速越野组BLDC开源项目,以此更好的支持广大参赛同学学习无刷电机控制技术,更好的做参赛准备,去年12月1日的开源项目可以通过点击以下标题跳转到原文进行查看。

逐飞基于MM32的极速越野BLDC开源项目

https://mp.weixin.qq.com/s/5IXpJs2btu1jjlJHGtGB7w

既然已经有一个灵动无刷驱动的开源方案了,为什么今天又有开源项目呢?就得从今年3月1日发布的灵动的新增的芯片支持计划说起了,可以通过这篇推文查看:

灵动第二批免费芯片发放说明

https://mp.weixin.qq.com/s/LOgciq_JK5rQI24DsTNmAg

同时灵动也希望逐飞能基于灵动提供的两颗电机芯片都制作出无刷驱动方案,一种方案是基于MM32SPIN360,一种方案是基于MM32SPIN27。于是就有了今天的开源项目发布:“逐飞基于MM32SPIN27PS的无刷驱动开源项目”

输入图片说明

一、无刷电机原理

无刷电机原理部分咱在这里就不再赘述了,新接触无刷电机或者想要再复习一下无刷电机旋转原理的同学可以看看上一篇灵动的无刷电机开源文章,再来一遍传送门:逐飞基于MM32的极速越野BLDC开源项目

二、SPIN27芯片介绍

2.1、芯片基本参数

本次开源的无刷驱动芯片使用灵动的MM32SPIN27PS作为控制芯片。

输入图片说明

这款单片机特点如下:

1.使用高性能的 Arm® Cortex®-M0 为内核的 32 位微控制器。

2.最高工作频率可达 96MHz。

3.包含两个12 位的 ADC,采样速度高达 1MHz。

4.通用定时器5 个、针对电机控制的 PWM 高级定时器2 个。

  1. UART 接口2 个、I2C 接口1 个、SPI 接口2 个。

6.针对无刷电机应用内置 3 个运放,3 个比较器。

2.2、芯片特点

2.2.1、PWM高级定时器1/8

该芯片的TIMER1与TIMER8定时器,可以直接输出三路PWM信号或者是三路互补的PWM信号,当是互补的PWM信号时可以设置死区,无刷电机的三个半桥通过我们有三种驱动方式。

方式一:上桥给PWM信号,下桥通过IO控制开启与关闭(逐飞本次开源项目即使用的这种方式)。

方式二:上桥通过IO控制开启与关闭,下桥给PWM信号。

方式三:上下桥都给PWM信号,但是需要注意的是上下桥的PWM信号必须是互补的,因为上下桥不能同时导通,否则出现电源与地短路的情况,由于MOS开关具有延时,所以互补PWM信号还必须设置死区,作用是当其中一个桥关闭之后要延时一段时间再打开另外一个桥,避免出现电源对地短路的情况。插入死区之后的互补PWM信号如下图所示(使用逻辑分析仪采集到的波形)。

输入图片说明

2.2.2.单片机集成比较器

该芯片内置三个比较器,如果采用六步方波无传感器的方式驱动无刷电机,那么势必会用到过零检测来判断何时进行换相,内置了比较器也为无传感器控制无刷电机带来了更多的便捷。在使用霍尔有感的方式我们也可以使用比较器来实现自动(这里的自动表示无需代码干预即可实现)堵转保护等功能。

2.2.3.单片机集成运放

该芯片内置了三个运放,可以用于电流检测,使用磁场定向控制(FOC),或者检测线路电流从而判断是否堵转等故障出现,然后及时关闭控制避免硬件出现损坏。内置运放进一步简化了电路降低了制作的难度。

三、硬件原理图

由于单片机内部已经集成了运放、比较器、预驱,因此外围器件选择主要就集中在了MOS管型号的选择上,MOS管我们选择的型号是TPH1R403NL,这款MOS电流高达150A,10V的时候内阻低至1.2毫欧,开启电压低至2.5V左右,性价比较高,因为灵动的电机驱动专用芯片集成功能丰富,所以用它加上MOS就简单的构成了无刷电机驱动硬件方案。具体原理图部分可以看下图,图看不清不要紧,我们稍后会放在Gitee进行开源,下载PDF即可查看。

输入图片说明

输入图片说明

本次开源的MM32SPIN27PS无刷驱动硬件部分与上次使用MM32SPIN360C的硬件部分基本一致,仅更改了串口调试部分和信号输入输出端口,并且新增了晶振电路,其他部分则未作修改。

输入图片说明

四、程序部分

4.1、MM32SPIN27PS无刷驱动开源项目的源码

4.1.1、开源项目的工程目录结构

逐飞Infineon智能车BLDC开源项目的目录结构如下图所示。

输入图片说明

CODE文件夹下放置的是逐飞科技精心编写的无刷电机驱动相关代码。

sdk是灵动官方的底层驱动,如果还需要其他的单片机片内外设功能,可以基于sdk文件下的底层自行编写程序实现。

zf_common、zf_driver和zf_device则是逐飞基于MM32SPIN27PS制作的底层库。

user_c文件夹下放置的是主程序及中断文件。

4.1.2、无刷电机驱动需要用到的相关内外设以及驱动代码

输入图片说明

无刷电机需要用到的单片机片内外设有:

ADC:主要用于检测电源电压、采集放大时候的母线电流以及相电流

高级定时器1:主要用于输出电机所需要用到的互补PWM信号,并且实现自动堵转保护,无需代码干预,当母线 电流超过设定值的时候,自动关闭定时器输出。

GPIO:主要用于LED指示灯,用于显示各种状态,并且初始化输出方向信息和速度信息的端口。

PWM输入:使用高级定时器8的输入捕获实现对外部PWM信号的周期以及占空比获取。

无刷电机的驱动文件有:bldc_config.h文件用于配置电机参数,例如是否开启闭环、是否开启刹车、最大转速设置。hall文件主要用于检测霍尔的值、换相时间计算、转速计算。motor文件主要用于电机占空比输出、速度计算、速度和方向信息输出。move_filter文件主要用于,对数据进行滑动平均滤波。pid文件主要用于对转速进行速度PID闭环。

4.1.3、主函数及中断函数说明

主函数与中断的文件存放在USER文件夹中,无刷电机控制部分由GTM模块硬件完成,所以并没有代码用于控制无刷电机,中断相关的函数全部放在了isr.c中。

4.2、MM32SPIN27PS无刷驱动开源项目的程序工作流程讲解

为了更清楚的表达起工作流程,整个项目的软件流程绘制了几张流程图,同时也加以文字说明。

4.2.1、主函数流程图

输入图片说明

上图为本次开源驱动程序的主函数部分,不难看出来,与上次开源的360C主函数部分基本一致,主循环主要负责将当前电机和驱动板的状态通过LED灯输出,并且将部分电机参数发送到虚拟示波器,因此主函数并不执行电机控制的部分,控制部分通过ADC采集中断来触发。

4.2.2、ADC中断流程图

输入图片说明

ADC中断是无刷电机的核心中断,ADC触发采集是由定时器1的通道4占空比更新事件进行触发的,因此ADC中断频率与TIMER1输出的PWM频率是一致的。PWM频率是40KHz,因此ADC的中断频率也是40KHz。

在中断内主要是获取母线电流、相电流、电源电压。母线电流在之后做电流环的时候需要使用到,也可以用于做故障检测,当检测到电流过大的时候,及时关闭输出以保护硬件,相电流可以用于之后做FOC驱动方案的时候提供支持。

扫描霍尔这个流程块中,主要是统计每次换相的时间,如果换相时间过长则认为出现故障此时应该及时关闭输出。当电机正常运行的时候将每次换相的时间都保存在数组内,当得到最近6次的换相时间之后,我们就能知道电机转动一圈所花费的时间,从而就能够计算出电机的转速了。在每次换相的时候更改速度输出引脚的PWM频率,这样外部控制器也能轻松的检测到电机的转速,而无需外加编码器。然后根据读取到的霍尔值计算出下次期望的霍尔值。

霍尔扫描结束之后,开始检查延时换相时间是否到,时间没有到则延时时间减一,延时时间为0的时候开始进行换相动作,这里延时换相的原因是因为在电机高速运转的时候霍尔有滞后导致的,可能有人问为什么霍尔滞后了,你还要延时换相呢?因为我们采用的方法是,当霍尔出现滞后之后,我们换相的时候并不是换到下一相,而是换到了下下相,这样就相当于超前换相了,所以我们需要加一定的延时去匹配,从而得到一个最佳的换相点。

4.2.3、定时器中断流程图

输入图片说明

定时器3中断频率为1KHz,主要用于根据DIR引脚设置电机是正转还是反转,然后计算速度曲线,用于实现电机缓慢加速(此功能可关闭),缓慢加速降低电机加速时功率,在调试阶段可以尽量保护车模以及硬件电路。然后进行PI闭环调节,这里主要实现是将我们采集到的电机速度与设置的电机速度求差,将得到的偏差系数KP得到比例输出Pout,然后对偏差系数KI并将每次计算出的结果进行求和得到Iout,最终将Pout与Iout相加,然后将相加之后的和输出到占空比寄存器驱动电机运转。其中KP、KI系数可能需要自己再多多调试,以找到更加完美的参数,使得电机运行更加迅速且稳定。

输入图片说明

定时器8中断主要作用是用来接收外部PWM信号的周期与高电平时间,然后计算信号的占空比,根据占空比的大小设置电机的转速,从而实现外部控制器来控制电机的转速。

五、逐飞制作的参考学习驱动板及无刷电机推荐

5.1、基于灵动MM32SPIN27的无刷电机驱动学习板使用简介

输入图片说明

上图中1-8号标号的含义如下:

1、直流电源接口,使用12V电源供电,建议使用3S电池。

2、控制输入与信息输出端口,PWM引脚是速度调节端口,外部控制器输出PWM,通过调节占空比大小来调节速度。DIR引脚是用于设置电机转动方向的;SPDOUT与DIROUT引脚是输出电机转速信息的,电机转得越快此引脚上输出的信号频率越高,推荐使用单片机采集编码器的接口进行信息采集。SPDOUT连接编码器采集接口的A通道或者连接单片机的计数通道,DIROUT连接编码器采集接口的B通道或者连接方向引脚(具体可以参考编码器采集例程)。

3、SWD调试接口,可以对电机驱动上的单片机烧写程序以及在线调试。

4、无刷电机接口,接入无刷电机的A、B、C三相。

5、无刷电机霍尔接口,连接无刷电机霍尔接口。霍尔接口可通过淘宝搜索“ZH1.5 6P“找到

6、电机驱动使能开关,开关是连接到IO上,通过单片机硬件实现的使能。

7、电源LED灯,给驱动供电时此灯亮起。

8、使能LED灯,打开开关时此灯亮起。

9、运行LED灯,当无刷电机运行时此灯亮起。

10、错误指示LED灯,当无刷电机堵转时此灯亮起。

温馨提示:该驱动板成品仅供学习参考调试,不能直接将成品驱动使用在正式参赛的小车上,正式参赛的无刷电机驱动板需要同学们自行制作并按要求在铜层打上队伍信息。

如果你申请到的是MM32SPIN360芯片,可以根据上一个基于灵动MCU的开源项目来制作自己的无刷电机驱动板,如果你申请到的芯片是MM32SPIN27,可以参考此开源项目来制作自己的无刷电机驱动板。

5.2、无刷电机推荐

前面的推文中有讲到过,我们对很多款电机进行了测试,后面也与其中一家无刷电机的生产商进行了合作,让其定制一款无刷电机供我们竞赛中使用,目前已在现货发售中,逐飞推荐极速越野组使用这款无刷电机,逐飞的开源项目代码和硬件也是以这款电机为样品来进行测试的。

这款电机的参数如下:有感、三槽两极、2860Kv(Kv表示每增加一伏电压电机增加的转速,最高12V)、尺寸36(mm)*50(mm)、额定功率190W、支持1-3S锂电池供电。

输入图片说明

逐飞无刷电机

输入图片说明

逐飞无刷电机与驱动接线示意图

温馨提示:此款电机仅为逐飞推荐款,同学们也可以选择自己认为合适的无刷电机,这一点上规则是没有限制的,但建议大家选择有感无刷。

六、总结

最后,上开源项目gitee链接:

https://gitee.com/seekfree/MM32SPIN27_BLDC_Project

打包下载开源库压缩包,就可以愉快的开始玩无刷啦,各位下载之前别忘了帮我们点一点小星星哦,感谢各位的支持。

逐飞会对本开源项目进行持续更新和维护,预计功能上还会继续添加串级闭环的功能,速度环作为外环,电流环作为内环,刹车力度可调节,这样可以不需要曲线计算即可实现电机缓慢加速的功能,通过内部电流环限定电流大小也能更好的保护硬件电路。之后也会尝试使用FOC方案驱动电机。当然,对这些功能有兴趣的同学可以自己提前研究尝试一下,听灵动的电机专家说,这些东西完全搞明白之后,都足够找一份相对不错的工作了。

特别说明:该开源项目仅用于各参赛同学在设计自己的小车时进行参考,硬件和软件都不能够直接拷贝使用在自己的作品中,请大家参考后重新完成硬件和软件的设计制作。

好了,本期的开源项目介绍就到这里了,推荐款无刷电机、无刷驱动学习板及越野组学习套件已上架逐飞淘宝店(seekfree.taobao.com),感谢各位支持,你们的支持是我们开源的动力,如果能帮到大家,深感荣幸。时间紧张,水平有限,大神轻拍,如果开源项目中有任何BUG,欢迎留言反馈,逐飞会持续维护和完善,也可通过QQ群与我们进行交流讨论(MM32极速越野组交流群--逐飞科技:1077051054)。欢迎各位持续关注“逐飞科技”微信公众号,逐飞的开源项目及相关信息更新都会在该公众号上发布,点击下方通道即可关注。

GNU GENERAL PUBLIC LICENSE Version 3, 29 June 2007 Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its authors. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things. To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users. Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS 0. Definitions. "This License" refers to version 3 of the GNU General Public License. "Copyright" also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. "The Program" refers to any copyrightable work licensed under this License. Each licensee is addressed as "you". "Licensees" and "recipients" may be individuals or organizations. To "modify" a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a "modified version" of the earlier work or a work "based on" the earlier work. A "covered work" means either the unmodified Program or a work based on the Program. To "propagate" a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well. To "convey" a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying. An interactive user interface displays "Appropriate Legal Notices" to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion. 1. Source Code. The "source code" for a work means the preferred form of the work for making modifications to it. "Object code" means any non-source form of a work. A "Standard Interface" means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among developers working in that language. The "System Libraries" of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A "Major Component", in this context, means a major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it. The "Corresponding Source" for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data communication or control flow between those subprograms and other parts of the work. The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding Source for a work in source code form is that same work. 2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law. You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary. 3. Protecting Users' Legal Rights From Anti-Circumvention Law. No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures. 4. Conveying Verbatim Copies. You may convey verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee. 5. Conveying Modified Source Versions. You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions: a) The work must carry prominent notices stating that you modified it, and giving a relevant date. b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to "keep intact all notices". c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it. d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so. A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an "aggregate" if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate. 6. Conveying Non-Source Forms. You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways: a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange. b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge. c) Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b. d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements. e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work. A "User Product" is either (1) a "consumer product", which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, "normally used" refers to a typical or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product. "Installation Information" for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM). The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network. Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying. 7. Additional Terms. "Additional permissions" are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission. Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms: a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or d) Limiting the use for publicity purposes of names of licensors or authors of the material; or e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors. All other non-permissive additional terms are considered "further restrictions" within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way. 8. Termination. You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11). However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material under section 10. 9. Acceptance Not Required for Having Copies. You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so. 10. Automatic Licensing of Downstream Recipients. Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance by third parties with this License. An "entity transaction" is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party's predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents. A "contributor" is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's "contributor version". A contributor's "essential patent claims" are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, "control" includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version. In the following three paragraphs, a "patent license" is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To "grant" such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. "Knowingly relying" means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient's use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it. A patent license is "discriminatory" if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law. 12. No Surrender of Others' Freedom. If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program. 13. Use with the GNU Affero General Public License. Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the combination as such. 14. Revised Versions of this License. The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License "or any later version" applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. 15. Disclaimer of Warranty. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. Limitation of Liability. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 17. Interpretation of Sections 15 and 16. If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively state the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. <one line to give the program's name and a brief idea of what it does.> Copyright (C) <year> <name of author> This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. Also add information on how to contact you by electronic and paper mail. If the program does terminal interaction, make it output a short notice like this when it starts in an interactive mode: <program> Copyright (C) <year> <name of author> This program comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details. The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, your program's commands might be different; for a GUI interface, you would use an "about box". You should also get your employer (if you work as a programmer) or school, if any, to sign a "copyright disclaimer" for the program, if necessary. For more information on this, and how to apply and follow the GNU GPL, see <http://www.gnu.org/licenses/>. The GNU General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. But first, please read <http://www.gnu.org/philosophy/why-not-lgpl.html>.

简介

受组委会及灵动委托,逐飞科技针对第十七届智能汽车竞赛室外极速组的BLDC应用需求,精心设计了符合赛事需求的MM32 BLDC驱动开源方案供大家参考,该方案使用MM32SPIN27,此单片机具有3个运放及3个比较器,无需外加运放与比较器。电机为内转子、2860Kv、电压为12V。开源项目具有的功能,目前支持电机正反转、内部速度闭环、支持刹车、支持电机加速度可调、支持堵转保护。 展开 收起
C 等 2 种语言
GPL-3.0
取消

发行版

暂无发行版

贡献者

全部

近期动态

加载更多
不能加载更多了
C
1
https://gitee.com/seekfree/MM32SPIN27_BLDC_Project.git
git@gitee.com:seekfree/MM32SPIN27_BLDC_Project.git
seekfree
MM32SPIN27_BLDC_Project
逐飞科技基于MM32SPIN27的智能车BLDC开源项目
master

搜索帮助